background image

Hy-Gain TH-1 Rotatable Dipole                                                                                Instructions 

 

2

 

Hy-Gain TH-1 4-Band Rotatable Dipole 

 
INTRODUCTION 

 

The Hy-Gain TH-1 is a 26 foot 20-, 15-, 10-and 6-meter full legal limit rotatable dipole that is 
inconspicuous and low profile, making it almost invisible from across the street. With its 13-foot 
turning radius and 8-pound weight, it fits on even small roofs and is perfect for town houses, 
apartments and condos - and can easily be turned by a lightweight TV rotator such as the HyGain 
AR-35.  If necessary, the TH-1 can even be mounted inside an attic! 

And this antenna is no wimp! Its bidirectional pattern can help reduce QRM and/or noise while 
maximizing your signal in the directions that you want -- so you can work some real DX. High 
efficiency traps provide operation up to a full 1500 Watts SSB/CW on 20, 15, and 10 meters.  Stub 
matching is used on 6 meters for 1500 watt operation on this band as well.   

The Hy-Gain TH-1 is built-to-last – using an incredibly strong solid rod fiberglass center insulator and 
6063 T-6 aircraft strength aluminum tubing for the radiator. And it assembles in about an hour.  

 

WARNING: Improper installation and assembly can be hazardous!  Read these instructions 
thoroughly before attempting to assemble, install or operate this product!  High power 
transmitting devices produce voltages that can cause severe burns or other injuries. 

 

SPECIFICATIONS 

 
Electrical Specifications 
 
 

 

 

Power   

 

Band  

CW SSB 

2:1 SWR BW Gain Front-to-Side 

20m 

 

1500  1500     200 KHZ 

0 dBd      20 dB 

15m 

 

1500  1500     400 KHZ 

0 dBd      20 dB 

10m 

 

1500  1500     1.1 MHZ 

0 dBd      20 dB 

 6m 

 

1500  1500     600Khz 

0 dBd      20 dB 

 
Mechanical Specifications 
 
Mast Size: 

 

1- to 1-1/2” diameter 

Overall Length: 

26 feet 

Turning Radius: 

13 feet 

Weight:   8 

pounds 

Wind Load: 

 

1 square foot 

 
 
 

 
 
 
 

Содержание TH-1










Отзывы: