Hy-Gain Discoverer 7-1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

background image

Figure 7

"Hairpin" Attachment Near 40-Meter

Insulator

Final Assembly

Select the 1 1/4" tubing clamps (Item No. 41)
and appropriate hardware and assemble as
shown in Figure 6. Strip your coax cable, install
solder lugs (not supplied) and connect to the
dipole. Tape the cable to the boom for strain
relief.

An RF choke made from 12 turns of RG-123/u
coax in a 14" diameter circle is recommended
with the split coax feed. An alternative
method is to use a Hy-Gain BN-86 50 ohm
balun for easy connection to your coax cable.
"Pigtail" leads of #10 gauge stranded wire 7
inches long should be used from the balun to
the tubing clamps.

«
...
9
10
11
12
13
...
»

Содержание Discoverer 7-1

















Отзывы:

Нет отзывов

Похожие инструкции для Discoverer 7-1

Бренд: M2 Antenna Systems Страницы: 5

Taco Antenna D4000 Series

Бренд: WADE Antenna, Inc. Страницы: 9

Бренд: Parsec Technologies Страницы: 19

Бренд: Radio Shack Страницы: 7

Бренд: l-com Страницы: 2

Televes Ellipse 148910

Бренд: T-Force Страницы: 2

HDView360 MINI-STATE HDMS9100

Бренд: AntennaCraft Страницы: 12

Mobile Big Stick MFJ-1652

Бренд: MFJ Страницы: 8

Бренд: Strong Страницы: 21

Бренд: Channel Master Страницы: 28

Бренд: Zehnder Rittling Страницы: 9

Бренд: RCA Страницы: 1

CMAX-DMF-43-UW-i53

Бренд: CommScope Страницы: 5

Бренд: TransWorld Antennas Страницы: 17

Бренд: Philips Страницы: 6

Бренд: Televes Страницы: 32

Бренд: Sirio Antenne Страницы: 2

Бренд: A.H. Systems Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды