Hy-Gain 2085-1 Скачать руководство пользователя страница 9

Hy-Gain 

Warrants to the original owner of this product, if manufactured by 

Hy-Gain

and purchased from an authorized dealer or directly from 

Hy-Gain

 

to be free from

defects in material and workmanship for a period of 12 months for rotator products and
24 months for antenna products from date of purchase provided the following terms of
this warranty are satisfied.

1. The purchaser must retain the dated proof-of-purchase (bill of sale, canceled check,

credit card or money order receipt, etc.) describing the product to establish the
validity of the warranty claim and submit the original or machine reproduction of
such proof of-purchase to 

Hy-Gain 

at the time of warranty service. 

Hy-Gain

 

shall

have the discretion to deny warranty without dated proof-of-purchase. Any evidence
of alteration, erasure, or forgery shall be cause to void any and all warranty terms
immediately.

2. 

Hy-Gain

 

agrees to repair or replace at 

Hy-Gain’s

 

option without charge to the

original owner any defective product under warranty, provided the product is
returned postage prepaid to 

Hy-Gain

 

with a personal check, cashiers check, or

money order for $8.00 covering postage and handling.

3. Under no circumstances is 

Hy-Gain

 

liable for consequential damages to

person or property by the use of any 

Hy-Gain

 

products.

4. Out-of-warranty Service: 

Hy-Gain

 

will repair any out-of-warranty product

provided the unit is shipped prepaid. All repaired units will be shipped COD to
the owner. Repair charges will be added to the COD fee unless other
arrangements are made.

5. This warranty is given in lieu of any other warranty expressed or implied.

6. 

Hy-Gain

 

reserves the right to make changes or improvements in design or

manufacture without incurring any obligation to install such changes upon any of
the products previously manufactured.

7. All 

Hy-Gain 

products to be serviced in-warranty or out-of-warranty should be

addressed to 

hy-gain, 308 Industrial Park Road,

Mississippi 39759, USA 

and must be accompanied by a letter describing

the problem in detail along with a copy of your dated proof-of-purchase.

8. This warranty gives you specific rights, and you may also have other rights which

vary from state to state.

LIMITED WARRANTY

Содержание 2085-1










Отзывы: