manualshive.com logo in svg

HWH 625 Series, Руководство оператора

Поделиться
Скачать
HWH 625 Series Скачать руководство пользователя страница 12

OPERATING PROCEDURES

ROOM RETRACT PROCEDURE FOR ROOMS WITH TRAVEL CLAMPS

2.  Turn the ignition switch to ACCESSORY.

3. Turn the room control panel KEY SWITCH

4.  To retract the room press and hold the 
ROOM CONTROL SWITCH in the "RETRACT" position 
until the room is fully retracted and both Travel Clamps

halt the operation of the room.

5. Turn the room panel KEY SWITCH to the "OFF" position.

6.  Turn the ignition switch off.

IMPORTANT: Room-locking devices should be locked 
while traveling.

CAUTION:

CLEAR OF ROOM WHEN OPERATING.

KEEP PEOPLE AND OBSTRUCTIONS

7.  If the room will not retract see the MANUAL ROOM
RETRACT PROCEDURE.

NOTE: Releasing the ROOM CONTROL SWITCH will 

1-800-321-3494.

contact HWH Customer Service for assistance

force the room.  DO NOT reverse direction of the room,

release the room control switch immediately.  DO NOT

retract the room until the room has been fully extended.

direction of the room has been reversed,  DO NOT

be reversed, but watch for binding of the room.  If the

retracted.  If necessary, the direction of the room may

reverse direction of the room until the room is fully

IMPORTANT: If either side of the room stops moving,

NOTE: During normal operation of the room, do not

MP35.3860

23JUL03

1.  The park brake must be set.  The room will not operate
if the park brake is not set.

to the "ON" position.

Engaged light come on.

IMPORTANT:  When the room is fully retracted, a room
in limit switch will allow the Travel Clamps to extend.
The hydraulic pump will run for approximately 5 seconds
after the room is fully retracted.  It will take the Travel
Clamps approximately 20 seconds to extend after the 
room is fully retracted.  When the Travel Clamps are fully 
extended, the 2 Travel Clamps Engaged lights will come
on.  When both Travel Clamps Engaged lights are on, the 
room control switch should be released.  If the Travel 
Clamps Engaged lights do not come on, DO NOT hold 
the room control switch to RETRACT for longer than 
40 seconds after the room extension is fully retracted.

NOTE: It is recommended to retract room extensions
before retracting jacks.

Содержание 625 Series










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды