background image

CONTROL FUNCTIONS

This light indicates the system is on.

This button turns off control power to the

These two levers are used to retract the

jacks into the STORE/TRAVEL POSITION for travel.  They
must be in "OPERATE" POSITION for leveling.                                                                    

pushing the  jack control lever to  one of the "RAISE"  positions.
This movement of the lever activates the pump and directs
hydraulic fluid to the jacks.  When the lever is released it will return
to the neutral (center) position, turning off the pump and stopping
jacks in position.                                                                                

PART IV

HWH HYDRAULIC LEVELING

UNDERSTAND OPERATOR’S MANUAL BEFORE USING.  BLOCK FRAME AND TIRES

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

OFF

CAUTION!

ON

5 AMP

FUSE

FUSE

NOT IN

PARK/

BRAKE

MI35.2503

27AUG97

CONTROLS

INDICATORS

EXTEND

RIGHT

HWH   HYDRAULIC LEVELING

"CAUTION"

REMOVING TIRES OR CRAWLING UNDER VEHICLE.

BLOCK FRAME AND TIRES SECURELY BEFORE

UNDERSTAND OPERATOR’S MANUAL BEFORE USING.

REAR

FRONT

LEFT

EXTEND

EXTEND

EXTEND

OPERATE

STORE

REAR

FRONT

STORE

OPERATE

A buzzer will sound if a jack is extended

two inches or more and the ignition switch is ON.                              

the electrical relay on the pump, the LEVELING LIGHTS,

or the WARNING BUZZER.  The ignition switch controls
power to these.

leveling and room extension systems.

This light illuminates when

the "ON" button is pushed and the parking brake has not been

A yellow LEVELING LIGHT indicates the

side or end of the coach that is low.  When the vehicle is level
all the LEVELING LIGHTS will be out.

A red WARNING LIGHT indicates the jacks

the WARNING LIGHTS, and the POWER ON LIGHT.
It does not control power to the "JACKS DOWN" LIGHT

that have extended two inches or more. A WARNING LIGHT
illuminates when its corresponding jack is extended at least two
inches and the POWER ON LIGHT is illuminated.

This light will illuminate when a jack

is extended two inches or more and the ignition switch is ON.

applied. The system will not turn on.

This button provides control power to operate

NOTE:

"ON" BUTTON:

"OFF" BUTTON:

STORE LEVERS:

JACK CONTROL LEVER:

POWER ON LIGHT:

This light must be on for the room extension to operate.

"NOT IN PARK/BRAKE" LIGHT:

LEVELING LIGHTS:

WARNING LIGHT:

WARNING BUZZER:

"JACKS DOWN" LIGHT:

START-UP & ADJUSTMENTS

Jacks are extended in pairs by 

POWER ON
LIGHT

"ON" BUTTON

"NOT IN
PARK/BRAKE"
LIGHT

"OFF" BUTTON

WARNING 
LIGHTS (4-Red)

LEVELING
LIGHTS (4-Yellow)

CONTROL
CIRCUIT FUSE
(5 AMP)

FRONT STORE
LEVER (OPERATE
POSITION)

REAR STORE
LEVER (OPERATE
POSITION)

FRONT STORE
LEVER (STORE/TRAVEL
POSITION)

JACK CONTROL LEVER

REAR STORE
LEVER (STORE/TRAVEL
POSITION)

Содержание 200 series

























Отзывы: