HWAM I 30/65 Скачать руководство пользователя страница 7

Page 7 of 20 pages

I

nstallatIon

 

manual

 

n general

Congratulations on your new HWAM insert. We are pleased that you have chosen a HWAM insert and 
confident that it will give you much pleasure. To ensure optimum operation and safety, we recommend 
that the installation should be carried out by an authorised HWAM retailer or a fitter recommended by 
the retailer. For an overview of HWAM retailer, visit www.hwam.com under “Retailer locations”.

Safety

The installation of your HWAM insert must always comply with all European, national and local building 
regulations. The installation must be carried out in accordance with the instructions in the installation 
and user manuals and subsequently registered with the local authorities. Upon installation, the chimney 
sweep must approve the installation before you can start using the insert. All HWAM insert packaging 
material must be handled in accordance with local waste management regulations.

Room requirements

Always ensure a supply of fresh combustion air to the room where the insert is to be installed. The insert 
uses approx. 16-37 m

3

 of air per hour (depending on the setting of the air control lever). A window that 

can be opened or an adjustable air valve will be sufficient. It must not be possible to block the adjustable 
air valve/grate. In newly built/airtight dwellings, we recommend that a fresh air system should be installed 
for the direct supply of external air to the combustion. This fresh-air system may be bought separately.

Before installing the insert, make sure that the floor can carry the insert, the chimney and any other 
parts required for the installation.

Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes 
be treated as a combustible wall, in which case we ask you to contact your local chimney sweep or glass 
producer to hear at what distance the insert should be kept from glass.

Technical measures and data

Test results from nominal test EN 13240

Nominal heating effect

10.0 kW

Flue gas temperature EN 13240 measurement point

302ºC

Flue gas temperature measured in the outlet socket

350ºC

Exhaust gas flow

9.07 g/s

Efficiency

78.5 %

Annual efficiency (EcoDesign)

68.5 %

PM

28 mg/m

3

OGC

120 mg/m

3

NOx

93 mg/m

3

CO at 13% O

2

1500 mg/m

3

CO at 13% O

2

0.12 %

Energy efficiency index

104

Energy efficiency class

A

Test result based on NS 3058

Particle emissions

-

The declaration of performance (DoP) can be downloaded from our website, www.hwam.com. 

Содержание I 30/65





















Отзывы: