FULL HD-TVI(1080P)
IR D&N DOME CAMERA
SK-D300IR(D)/HT21AI
MANUAL
1. Opening the dome :
Pushing the latch button.
(Remove
the
protection
sheet after installing.)
◐ HOW TO INSTALL
2. Removing the dome :
Lift the dome. When you
push the latch button, it is
unlocked and you can lift
the dome.
1. 1/2.9" Sony CMOS sensor
2. Full HD(1920x1080) Resolution
3. DAY & NIGHT Function
4. WDR (Wide Dynamic Range) Function
5. 3D DNR Function
6. Privacy mask function 16 area
7. On Screen Display menu
8. Intelligent motion detection
9. Output : HD-TVI/CVBS
10. Protocol Pelco-C
11. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope
mountable
12. 20M range visible in total darkness with 24pcs of IR LEDs.(Indoor)
13. Up to 500M Full HD-TVI Tranmission via Coaxial cable.(Maximum
tranmission distance may vary with type of coaxial cable)
◐ FEATURES
◐ DIMENSION
◐ ASSEMBLY
1. Do not install the camera outdoors.
2. Choose an ideal location for the camera, since a camera unit must
be protected against vibration.
3. Be careful not to scratch the camera unit, especially lens or dome
cover.
4. Use the camera within the temperature(-45℃~50℃).
5. Avoid any direct sun light toward the lens.
6. Use the AC adaptor 12V DC, 600mA regulated. Dual voltage
product can use 24V AC, 600mA adaptor.(option)
◐ PRECAUTION
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
3. Camera installation :
(1) Fix the camera set with the supplied
screws on ceiling or wall mount. If you
don't use supplied screws, the camera
may fall off.
(2) Please refer to '4. Camera angle
adjustment' regarding adjust camera
angle.
(3) Lens adjustment(Vari-focal Lens only)
After opening the LED cover,
① By turning the "Tele-Wide" knob, you can access a range of
focal lengths within specified limits.
② Since then, by turning the "Near-Far" knob, you can set the
focus toward the wanted object.
(4) Re-assemble the camera.
1
2
w
N
F
T
4. Camera angle adjustment :
(1) Pan adjustment : Grasp the disk of camera and then adjust
direction to the right or left(-180°~180°)
(2) Tilt adjustment : Grasp the LED cover of camera and then adjust
direction to the up or down(6°~ 90°)
(3) Roll adjustment : Grasp the camera holder and then rotate
(-178°~178°)
<Caution> If you try to adjust the camera out of limited angle, it might
cause troubles and damage to camera.
Protection sheet
LATCH BUTTON
SCREW TP1
3.5x20 2EA
SCREW TP1
3.5x20 2EA
<Ceiling mount>
<Wall mount>
ROTATION
U
D
R
L
LED COVER
DISK
CAMERA
HOLDER
Ø100
Ø130.8
Ø109
48.1
101
SK-D300(IR)
DOME COVER ASS’Y
SK-D300(IR)
CAMERA MODULE ASS’Y
SCREW
HARNESS
LED COVER
ASS’Y
SCREW
CONTROL PCB ASS’Y
PUSH BUTTON
DISK
BASE
CABLE
Take off the
marked part
by using nipper
for lpacing
cable out.
Hole
Fix the disk
(Pan angle)
using by a
screw driver
on M3X10
screws
in the holes
M3x10 SCREW
Take off the
marked part
by using nipper
for lpacing
cable out.
Hole
Fix the disk
(Pan angle)
using by a
screw driver
on M3X10
screws
in the holes
M3x10 SCREW
