HUSTLER Super Z Diesel Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 65

HUSTLER Super Z Diesel Скачать руководство пользователя страница 27

115164

5-1

REV D

ENGINE MAINTENANCE

General Engine Maintenance

Detailed instructions and recommendations for break-in

and regular maintenance are specified in the Engine Owner’s
Manual. Please refer to this manual for engine servicing,
lubricating oil levels with quality and viscosity
recommendations, bolt torques, etc. The engine warranty is
backed by the engine manufacturer. Special attention should
be paid to applicable data which will not be duplicated here.

Engine Oil and Filter

Check engine oil daily and after every 4 hours of operation.

Machine must be setting level when checking oil. Refer to
engine manual and maintenance schedule for oil
recommendation and capacities. Hustler

®

Motor Oil is

recommended.

Change the engine oil and filter after the first 5 hours of

operation and per the engine manufacturer’s
recommendations after that. If mower is being operated in
extremely dirty conditions, then it is recommended oil be
changed more frequently. IMPORTANT: When removing the
oil filter take precautions to minimize oil spillage on the
exhaust system.

The oil filter and oil drain plug are located on the

underneath side of the engine. Figure

Engine Air Filter

Perform engine air filter maintenance per the Maintenance

Schedule shown elsewhere in this manual.

A specially designed dry filter is standard equipment on

these mowers and supplies clean combustion air to the
engine. Figure 5-2

These mowers are equipped with a safety filter. The filter

element slides over the safety filter. Figure 5-3

The safety filter does not require servicing unless it

becomes contaminated with dirt or moisture.

Recommended service procedure

1. Release clamps and remove element. Clean the

canister with a damp cloth.

If the engine has been running and is up to
operating temperature, allow the engine to cool
before changing the oil. Engine and engine oil will
be very hot, so be very careful when changing oil
and wear the appropriate protective gear to avoid
being burned or exposed to engine oil.

A. Oil filter

B. Oil drain plug

Figure

5-1

WARNING

A

B

A. Canister
B. Dust cap

C. Pre-cleaner

Figure

5-2

A. Safety filter

Figure

5-3

A

C

B

A

«
...
25
26
27
28
29
...
»

Содержание Super Z Diesel


































































Отзывы:

Нет отзывов