HUSTLER FasTrak Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 37

HUSTLER FasTrak Скачать руководство пользователя страница 25

121363

6-3

REV C

Mower Blade Removal

IMPORTANT: Refer to the Safety section of this manual for

blade handling safety information.

A 15/16" wrench is required to remove the 5/8" cap screw

holding the blade to the spindle shaft. NOTE: A blade holding
tool (part number 381442) is available from Hustler

®

Turf

Equipment. It is designed to prevent the blades from rotating
when they are being removed or installed on the spindle. Con-
tact your Hustler

®

Dealer for more information.

Do not re-use spindle bolts which have stripped, worn or

undercut threads. Torque bolts on spindles to 118 ft-lbs
(160.0 N•m) when reinstalling blades.

Properly compressed cup washers maintain the correct

compression load on the blades. Replace the cup washers if
they are cracked or flattened.

IMPORTANT: The blade sail (curved part) must be point-

ing upward toward the inside of the deck to ensure proper
cutting.

A. Re-sharpening pattern
B. Original edge

Figure 6-5

Comparison of Warped and Straight Blades

A. Warped blade — replace
B. Straight blade

C. Cutting plane

Figure 6-6

Do not sharpen to original pattern (below). It

is easier to get a straight cutting edge follow-

ing the re-sharpening pattern shown above.

A

B

A

B

C

End view of blades, comparing twisted and straightened blades.

A. Twisted blade edge —

replace blade

B. Straight blade edge

C. Cutting plane

D. Cutting edge

Figure 6-7

Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves and use extra caution
when servicing them.

Failure to correctly torque the bolt may result in
the loss of the blade which can cause serious
injury.

A

C

D

D

B

WARNING

WARNING

«
...
23
24
25
26
27
...
»

Содержание FasTrak






































Отзывы:

Нет отзывов