HUSTLER FasTrak Super 928192 Скачать руководство пользователя страница 21

20

107708_0808

Fluid level should be at the “Full Cold” line on the expansion tank.  Use

only SAE 20W50 SL/SM service motor oil.

Initial system oil and filter change must be after the first 75 hours of use

or 1 year whichever comes first.  Thereafter, replace filter and oil in each
transaxle every 2 years or 200 hours, whichever comes first.  

NOTE:  

The

filter guard must be removed to access filter.

Each transaxle’s filter is located per Fig. 4-3.  A standard oil filter

wrench is used to change filter, threads are right handed.  Use a 

Hustler

Figure 4-2

Expansion tank

Figure 4-1

ZT 2800 integrated

pump/motor

Figure 4-3

Filter

Solid fill tires are not recommended

for Hustler turf equipment.  On

any machine, with solid filled tires, the warranty claim will be denied.

Lubrication

Use SAE multi-purpose grease.

Electrical system

The electrical system is a 12-volt, negative ground.  Recommended

battery size is a garden tractor BCI group U1R with 225 or better cranking
AMP rating.  A maintenance-free battery is recommended.  Otherwise,
follow battery manufacturer’s maintenance, safety, storing and charging
specifications. 

WARNING:  

Battery posts, terminals, and related

accessories contain lead and lead compounds, chemicals
known to the State of California to cause cancer and
reproductive harm.  Wash hands after handling.

WARNING:  

Charge batteries in an open well ventilated

area, away from sparks and flames.  Unplug charger before
connecting or disconnecting from battery.  Wear protective
clothing and use insulated tools.

WARNING:  

Avoid skin and clothing contact with battery

acid.
Always wear eye protection when checking the battery, acid
can cause serious injury to skin and eyes.  If contact occurs,
flush area with clean water and call physician immediately.
Acid will also damage clothing.
Do not drink the battery electrolyte.
Do not allow open flame near the battery when charging.
Hydrogen gas forms inside the battery.  This gas is both toxic
and flammable and may cause an explosion if exposed to
flame.  Always remove the negative ground first and replace
it last.
Do not overfill battery.
Electrolyte may overflow and damage paint, wiring or
structure.  When cleaning the battery, use soap and water.  Be
careful not to get soap and water into the battery.  Clean the
battery terminals with a solution of four parts water and one
part baking soda when they become corroded.

WARNING:  

Shorts caused by battery terminals or metal

tools touching metal tractor components can cause sparks.
Sparks can cause a battery gas explosion which will result in
personal injury.
Prevent the battery terminals from touching any metal tractor
parts when removing or installing the battery.
Do not allow metal tools to short between the battery
terminals and metal tractor parts.

WARNING:  

Incorrect battery cable routing could cause

damage to the tractor and battery cables.  This can cause
sparks which can cause a battery gas explosion which will
result in personal injury.
Always 

disconnect

the negative (black) battery cable(s)

before disconnecting the positive (red) cable(s).
Always 

connect

the positive (red) battery cable(s) before

disconnecting the negative (black) cable(s).

Hydraulic system

These units are equipped with two Hydro-Gear ZT 2800 transaxles.

Fig. 4-1

IMPORTANT:  

Never use hydraulic or automatic transmission fluid in

this system; use only motor oil as specified.  Remember, dirt is the primary
enemy of any hydraulic system.

The hydraulic expansion tank is located in front of the engine and under

the operator’s platform.  Fig. 4-2

Check oil level in hydraulic system after every 50 hours of operation or

weekly, whichever occurs first.  Check more often if system appears to be
leaking or otherwise malfunctioning.

Содержание FasTrak Super 928192



































Отзывы: