manualshive.com logo in svg

Husqvarna Z48, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Husqvarna Z48 Скачать руководство пользователя страница 6

6

UNPACKING INSTRUCTIONS

•

Remove all parts and packing materials
from carton.

•

Check carton contents against list. Be sure
all parts are there.

TOOLS REQUIRED FOR ASSEMBLY

(2) 1/2" Wrenches
(1) 9/16" Wrench
(1) 9/16" Socket wrench

CARTON CONTENTS:

3 - Container Tops

1 - Weight Brackets

3 - Container Bottoms 2 - Screws #10-12 x 1
1 - Upper Chute

6 - Screw #10-12 x 1 1/4

1 - Lower Chute

4 - Bolts 5/16-18 x 3/4"

1 - Catcher Mount

2 - Nut 3/8-16 Nyloc

1 - Cover Assembly

2 - Bolt 3/8-16 x 2, Gr5

1 - Cast Weight

4 - Washer 1/4

PARTS IDENTIFICATION

NOTE: 

When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you

are seated on the mower in the operator’s position.

CAUTION

BEFORE ASSEMBLING GRASS CATCHER TO MOWER:
• Set parking brake.
• Place motion control levers in "NEUTRAL "  position.
• Turn ignition key "OFF" and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug and place wire where it cannot come in contact with plug.

COVER
ASSEMBLY

GRASS
CATCHER
CONTAINERS

DUMP BAG
INDICATOR

CHUTE LATCH

UPPER CHUTE

LOWER CHUTE

LOWER CHUTE
ATTACHING
STRAPS

Содержание Z48





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды