Husqvarna TS 350E Скачать руководство пользователя страница 13

WARRANTY CONDITIONS

1. PERIOD

The warranty is acknowledged as of the date of purchase (date of the invoice of the distributor) and is valid for a period of 12 
months.

2. WARRANTY

The warranty is limited to the free of charge replacement of parts recognised as defective by Husqvarna (excluding wear 
components and consumables) providing the repair is made within after-sales service of Husqvarna or a recognised Husq-
varna repair centre.

The manufacturer is not responsible for any direct or indirect, material or immaterial, damages caused to persons or things by 
failure of the machine or the non operation of the machine.

3. WARRANTY CONDITIONS

To bene

fi

 t the warranty, it is necessary to return the joined warranty certi

fi

 cate, duly completed, to Husqvarna within eight 

days of the purchase.

In case of failure of the machine during the warranty period, our after-sales services will inform you of the appropriate and 
most effective method of dealing with your claim and advise you if necessary of your nearest approved service centre.

As an alternative, you may return, at your cost, the machine together with a written description of the problem and damages 
with a copy of the invoice directly to our after sales department where upon a full investigation will be instigated without 
delay.

4. EXCLUSIONS

Warranty will not be applied for damages or failures caused by :

- incorrect use, error in transportation, handling or maintenance,

- use of incorrect fuel or lubricants not advised by Husqvarna,

- use of non-genuine parts or accessories,

- repairs made by non approved service centres,

- use of incorrect speci

fi

 cations of cutting tools.(We suggest the use of Husqvarna tools).

The goods are returned at the sole responsibility of the Buyer who must appeal against the transporter in the usual manner 
without delay.

Operator’s manual - TS 350 E

Polish - 

13

Содержание TS 350E

















Отзывы: