Husqvarna TE 250 страница 78 Скачать руководство пользователя

Страница: 78 / 169

12 SERVICE WORK ON THE CHASSIS

–

Install the air filter box cover. (

p. 68)

12.32

Checking the chain for dirt

400678-01

–

Check the chain for heavy soiling.
» If the chain is very dirty:

–

Clean the chain. (

p. 76)

12.33

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 55)

400725-01

Main work

–

Rinse off loose dirt with a soft jet of water.

–

Remove old grease residue with chain cleaner.

Chain cleaner (

p. 157)

–

After drying, apply chain spray.

Off-road chain spray (

p. 157)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 55)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды