manualshive.com logo in svg

Husqvarna T540i XP, Руководство оператора, Страница: 23 / 32

Поделиться
Скачать
Husqvarna T540i XP Скачать руководство пользователя страница 23

• Round file diameter.

It is not easy to sharpen a saw chain correctly without

the correct equipment. Use Husqvarna file gauge. This

will help you to keep maximum cutting performance

and the kickback risk at a minimum.

WARNING: 

The force of the kickback

increases a lot if you do not follow the

sharpening instructions.

Note: 

Refer to 

Accessories on page 29

 for

information about sharpening of the saw chain.

To sharpen the cutters

1. Use a round file and a file gauge to sharpen the

cutting teeth.

Note: 

Refer to 

Accessories on page 29

 for

information about which file and gauge that

Husqvarna recommends for your saw chain.

2. Apply the file gauge correctly on to the cutter. Refer

to the instruction supplied with the file gauge.

3. Move the file from the inner side of the cutting teeth

and out. Decrease the pressure on the pull stroke.

4. Remove material from one side of all the cutting

teeth.

5. Turn the product around and remove material on

the other side.

6. Make sure that all cutting teeth are the same

length.

General information about how to adjust the

depth gauge setting

The depth gauge setting (C) decreases when you

sharpen the cutting tooth (A). To keep maximum

cutting performance you must remove filing material

from the depth gauge (B) to receive the recommended

depth gauge setting. See 

Accessories on page 29

 for

instructions about how to receive the correct depth

gauge setting for your saw chain.

A

B

C

WARNING: 

The risk of kickback

increases if the depth gauge setting is too

large!

To adjust the depth gauge setting

Before you adjust the depth gauge setting or sharpen

the cutters, refer to 

To sharpen the cutters on page 23

,

for instructions. We recommend you to adjust the

depth gauge setting after each third operation that you

sharpen the cutting teeth.
We recommend that you use our depth gauge tool to

receive the correct depth gauge setting and bevel for

the depth gauge.

1. Use a flat file and a depth gauge tool to adjust the

depth gauge setting. Only use Husqvarna depth

gauge tool to get the correct depth gauge setting

and bevel for the depth gauge.

2. Put the depth gauge tool on the saw chain.

Note: 

See the package of the depth gauge tool

for more information about how to use the tool.

1036 - 005 - 29.06.2020

23

Содержание T540i XP

































Отзывы:

Нет отзывов