Husqvarna R 316TsX Скачать руководство пользователя страница 11

• Do not turn more than necessary. Turn slowly and

gradually when you move down a slope. Move at low

speed. Turn the wheel carefully.

• Look out for and do not move across furrows, holes

and bumps. There is a higher risk that the product

overturns on ground that is not flat. Long grass can

hide obstacles.

• Do not cut grass near edges, ditches or banks. The

product can suddenly overturn if a wheel moves

across the edge of a steep slope or a ditch, or if an

edge gives way. If the product falls into water, there

is a risk of drowning.

• Do not mow wet grass. It is slippery, and tires can

lose their grip so that the product skids.

• Do not put your foot on the ground to try to make the

product more stable.

• Move very carefully if an accessory or other object is

attached that can make the product less stable.

• To make the product more stable, attach wheel

weights or counterweights. Speak to your dealer for

more information. On R 316TX AWD, R 316TsX

AWD, use counterweights since wheel weights can

not be used on AWD products.

Fuel safety

WARNING: Be careful with fuel. It is very

flammable, and can cause injury and

damage to property.

WARNING: Read the warning instructions

that follow before you use the product.

• Do not fill the fuel tank indoors.
• Gasoline and gasoline fumes are poisonous and

very flammable. Be careful with gasoline to prevent

injury or fire.

• Do not remove the fuel tank cap or fill the fuel tank

when the engine is on.

• Let the engine become cool before you refuel.
• Do not smoke when you fill fuel.
• Do not fill fuel near sparks or naked flames.
• If there are leaks in the fuel system, do not start the

engine until the leaks are repaired.

• Do not fill above recommended fuel level. The heat

from the engine and the sun makes the fuel expand

and the fuel overflows if the tank is filled too much.

• Do not fill too much. If you spill fuel on the product,

clean up the spill and wait until it is dry before you

start the engine. If you spill on your clothing, change

it.

• Store fuel in approved containers only.
• Store the product and fuel in such a way that there is

no risk that fuel leaks or fumes can cause damage.

• Drain off the fuel in an approved container outdoors

and away from naked flames.

Battery safety

WARNING: A damaged battery can cause

an explosion and cause injury. If the battery

has a deformation or is damaged, speak to

an approved Husqvarna service agent.

WARNING: Read the warning instructions

that follow before you use the product.

• Use protective glasses when you are near batteries.
• Do not wear watches, jewelry or other metal objects

near the battery.

• Keep the battery out of reach for children.
• Charge the battery in a space with good airflow.
• Keep flammable materials at a minimum clearance

of 1 m when you charge the battery.

• Discard replaced batteries. See 

Disposal on page

108

.

• Explosive gases can come from the battery. Do not

smoke near the battery. Keep the battery away from

open flames and sparks.

Transport safety

• Use an approved transport vehicle for transportation

of the product.

• A markets national or local regulations can set limit

to the transportation of the product.

• The operator of the transport vehicle is responsible

to attach the product safely during transport.

Safety instructions for maintenance

WARNING: The product is heavy and can

cause injury or damage to property or the

adjacent area. Do not do maintenance on

the engine or the cutting deck without these

conditions:
• The engine is off.
• The product is parked on a level surface.
• The parking brake is applied.
• The ignition key is removed.
• The cutting deck is disengaged.

844 - 002 - 

87

Содержание R 316TsX






































Отзывы: