Husqvarna PT26 D Скачать руководство пользователя | Manualshive

Страница: 54 / 80

background image

53

Lubrication

Chapter 7: Lubrication

Lubrication Schedule

When in daily use, the weekly lubrication (40 h) schedule should be carried out twice a week.

General

The position numbers for the lubrication points refer to
the lubrication instructions on the following pages.

Remove the ignition key to prevent unintentional
movements during lubrication.

When lubricating with an oilcan, it ought to be filled
with engine oil. When lubricating with grease, unless
otherwise stated, grease 503 98 96-01 or another
chassis or ball bearing grease offering good corrosion
protection shall be used.

With daily use, the machine shall be lubricated twice
weekly.

Wipe away excess grease after lubrication.

Lubricating the cables

Grease both ends of the cables and move the controls
to end stop positions when lubricating. Re-attach the
rubber covers on the cables after lubrication. Cables
with sheaths will jam if they are not lubricated
regularly. A jammed cable may cause malfunction,
such as the parking braking being applied.

= Filter replacement

= Oil Change

= Level check

= Brush

= Grease nipple

= Oil can

A. Radiator grille, See “Checking radiatorgrilles” on
page 79.

B. Pump and alternator belt, See “Replacing the
pump and generator drive belts” on page 81.

C. Power take-off belts, See “Replacing the power
take-off belts” on page 105.

D. Coolant, See “Cooling system” on page 50.

E. Cutting unit belt, See “Replacing the cutting unit
belt” on page 107.

F. Air filter, See “Servicing the air filter” on page 84.

G. Fuel filter, See “Servicing the fuel filter” on
page 87.

Symbols on the lubrication chart

«
...
52
53
54
55
56
...
»

Содержание PT26 D

















































































Отзывы:

Нет отзывов

Похожие инструкции для PT26 D

Бренд: Stiga Страницы: 294

LazerCut LCS405

Бренд: SANLI Страницы: 19

Бренд: Stihl Страницы: 514

Derby Stallion ZT2561

Бренд: Simplicity Страницы: 39

RANSOMES 933304J

Бренд: Textron Страницы: 28

Бренд: Neuton Страницы: 56

Бренд: Ozito Страницы: 6

Бренд: Yard Pro Страницы: 100

Бренд: Cramer Страницы: 216

Бренд: Kubota Страницы: 59

Бренд: Cub Cadet Страницы: 32

Бренд: Black & Decker Страницы: 40

Бренд: Black & Decker Страницы: 17

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 15

Бренд: Black & Decker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды