WARNING:
Obey the safety
instructions for the disinfectant.
1. Apply the disinfectant to the product surface.
2. Let the product become fully dry.
Service life of the product
The service life of the product is a maximum of 3 years
from the day the product is removed from the package.
This is valid if the package is not damaged and the
product is removed from the package at the time of
the purchase. The product must be discarded after a
maximum of 3 years of use.
If the product is not removed from the package at
the time of purchase and kept in storage correctly,
the possible service life is 5 years from the date of
manufacture.
The actual service life depends fully on the condition of
the product. The condition of the product is affected by
these factors:
• UV radiation
• Type and frequency of use
• Product handling and storage
• Climatic influences such as ice or snow
• Operational environments such as salt or sand
• Chemical influences such as battery acid
• Heat contamination
• Mechanical deformation or distortion
Extreme conditions during operation can shorten the
service life to a single use only. If the product is
damaged before its first use, for example during
transportation, it must be discarded immediately and not
used.
Mechanical wear and sunlight decrease the service life
considerably. Bleached or abraded fibers, discoloration,
and hardened spots are signs that show that the product
must be discarded.
The lifetime of an installed product depends also on
the condition of the tree and on how the product is
attached. After use, the product must be removed. It is
not designed for permanent installation in a tree.
To take the product out of service
If the product is subject to a fall or shows signs of wear
or damage, it must be taken out of service.
1. If you are sure that the product is damaged, discard
it.
2. If you think that the product can be damaged, do
these steps:
a) Put a clearly visible label or marking on the
product to prevent accidental use.
b) Let a competent person or the manufacturer do
the required tests and inspections.
If the competent person gives a written approval, the
product can be used again.
Transportation, storage and disposal
Transportation and storage
• Before transportation and storage, make sure that
the product is clean and dry.
• Put the product in a bag that gives protection from
moisture, light and dirt.
• Make sure that the storage space meets these
requirements:
• The temperature is 15–25°C.
• The air flow is sufficient.
• There is no sunlight, UV radiation or light from
welding equipment.
• There are no chemicals or other aggressive
environments.
• There are no objects with sharp edges.
Disposal
• Obey national regulations.
• Use the local recycling system.
Compliance and approvals
The following standards are applied:
• EN 795B:2012
• AS/NZS 5532:2013
• ANSI Z133-2017
The product meets the requirements of the ANSI
Z133-2017 standard for hitch cords (MBL ≥ 24,02kN for
the doubled hitch cord).
The product accompanied by this set of instructions
is type-examined, CE-marked to state conformity with
the European regulation (EU) 2016/425 on Personal
Protective Equipment (PPE) and meets the European
standards given on the product label. The product
does however not comply with any other standards
unless explicitly stated. Notified body 0408: TÜV Austria
Services GmbH, Deutschstrasse 10, A-1230 Vienna,
Austria.
This product was tested to EN 795, Class B, for use by a
single person using Personal Protective Equipment.
Pursuant to EN 795, this product for Personal Protective
Equipment must be capable of withstanding a force
of 18 kN in every described mode of use when new.
1751 - 003 - 16.03.2022
7
Содержание Prusik Eye-n-Eye 8 mm
Страница 107: ...1751 003 16 03 2022 107 ...
Страница 113: ...1751 003 16 03 2022 113 ...
Страница 114: ...114 1751 003 16 03 2022 ...
Страница 115: ...1751 003 16 03 2022 115 ...