Husqvarna ProFlex 21 Скачать руководство пользователя

Страница: 19 / 96

English-

PRESENTATION

Cutting height adjustment lever

Using the cutting height lever, the cutting height can
be adjusted between 7 different positions.

In order to obtain an equal cutting height, it is
important that the air pressure is the same in both
front wheels (60 kPa).

Lever for hydraulic lift of attachments,
PF 21

The lifting lever is used to put the cutting unit in either
the transport or mowing position when hydraulic
pressure is available.

In the transport position, the blade brake is
automatically activated so that the blades stop within
about 5 seconds.

Lifting the cutting unit (transport position)

Pull the lever backwards to engage the transport
position.

The unit is raised and the blades stop rotating.

Secure the cutting unit if necessary using the
mechanical lifting lever.

Lowering the unit (mowing position)

If the cutting unit is secured in the transport position
using the mechanical lifting lever, move the mechanical
lifting lever to the cutting position.

Move the hydraulic lifting lever forwards to engage the
cutting position. The unit is lowered and the blades
begin to rotate.

In order to ensure that the hydraulic cylinder is in the
outer position, hold the lever in the forward position
for a half to one second.

8009-557

8009-536

Raising the cutting unit with the hydraulic lifting lever

8009-538

Lowering the unit with the hydraulic lifting lever

Содержание ProFlex 21

































































































Результаты поиска

Содержание ProFlex 21

Отзывы:

Похожие инструкции для ProFlex 21

Бренды по названию

Популярные бренды

Husqvarna ProFlex 21, Руководство оператора

Результаты поиска

Содержание ProFlex 21

Отзывы:

Похожие инструкции для ProFlex 21

Бренды по названию

Популярные бренды