Husqvarna K960 Ring Скачать руководство пользователя страница 25

Страница: 25 / 28

English

– 25

MAINTENANCE

Trouble shooting

Mechanics

Symptom

Probable cause

The blade does not rotate.

Roller knobs not tightened fully.

The blade not fitted on guide rollers correctly.

Rollers tensioned too much.

The blade rotates too slowly.

Roller knobs not tightened fully.

Worn drive wheel.

The V-shaped inner diameter of the blade is worn.

The springs on the guide rollers are weakened.

Defective roller bearings.

The blade jumps out of its
position.

Roller setting too loose.

Worn guide rollers.

The blade not fitted on guide rollers correctly.

Damaged blade.

The blade warps.

Rollers tensioned too much.

Blade overheating.

Segments break.

Bent, twisted or badly maintained blade.

Continue to use the blade only if one segment is missing or leave for reconstruction when the
blade is worn max 50 %.

The blade cuts too slowly.

Wrong blade for the material in question.

The blade slips.

The guide rollers does not move in and out freely. A seized roller can not press the blade hard
enough against the drive wheel.

Worn drive wheel. Abrasive material and too little water when cutting increases the wear on
the wheel.

Worn guide roller flange. When more than half of the width of the flange is worn the blade
slips.

The blade’s groove and inner edge are worn. Caused by inferior flushing of abrasive material
and/or a worn drive wheel causing the blade to slip.

Содержание K960 Ring





























Результаты поиска

Содержание K960 Ring

Отзывы:

Похожие инструкции для K960 Ring

Бренды по названию

Популярные бренды

Husqvarna K960 Ring, Руководство оператора

Результаты поиска

Содержание K960 Ring

Отзывы:

Похожие инструкции для K960 Ring

Бренды по названию

Популярные бренды