manualshive.com logo in svg

Husqvarna HUV 4214 2009, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Husqvarna HUV 4214 2009 Скачать руководство пользователя страница 22

3

Using a Booster Battery (Jump Starting)

GENERAL INFORMATION

LIFTING THE ENTIRE VEHICLE

1.

Place vehicle on a level surface.

2.

Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL and set the
park brake. Chock the wheels.

3.

Disconnect battery and spark plug wire(s).

See Disconnecting the Battery – Gasoline Vehicles on page 1-4.

4.

If removing wheels, loosen the lug nuts.

5.

Lift one side of vehicle and support on jack stands

(Figure 3-5, Page 3-6)

.

6.

Lift other side of vehicle and support on jack stands.

7.

Remove the wheels.

1025

Figure 3-5

Jack Stand Placement

USING A BOOSTER BATTERY (JUMP STARTING)

See General Warning on page 1-2.

WARNING

• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face shield and

rubber gloves when working on or near batteries.

• When jumping from a booster battery, make the final connection the negative (-) cable.

• Do not jump start or charge a frozen or damaged battery. Unplug charger before connecting or

disconnecting cables to the battery. Never lean over battery while boosting, testing, or charging.

If it is necessary to use a booster battery to start the engine, BE CAREFUL!

1.

Turn the key switch to the OFF position. Place the Forward/Reverse handle in the NEUTRAL position, engage
the park brake and chock the wheels.

2.

Ensure the booster battery is 12-volt.

See following NOTE.

NOTE:

A starting battery is recommended but a deep cycle battery can be used if necessary.

3.

Access battery by removing the seat.

4.

Locate the vehicle battery on the passenger side of the vehicle.

Page 3-6

2009-2010 HUV 4214, HUV 4414, and HUV 4414X Maintenance and Service Manual

Содержание HUV 4214 2009




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды