Husqvarna GTH24V52LS/ 96048003601 Скачать руководство пользователя

Страница: 5 / 34

UNASSEMBLED PARTS

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.

ADJUST SEAT (See Fig. 2)

• Sit in seat.
•

Lift up adjustment lever (A) and slide seat until a com-

fortable position is reached which allows you to press

clutch/brake pedal all the way down.

• Release lever to lock seat in position.

Fig. 2

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Stan dard

wrench sizes are listed.
(1) 1/2" wrench

Tire pressure gauge

(2) 7/16" wrenches

Utility knife Pliers

When right or left hand is mentioned in this man ual, it means

when you are in the operating po si tion (seated be hind the

steer ing wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons

from carton .

• Cut along dotted lines on all four panels of carton.

Remove end panels and lay side panels flat.

• Check for any additional loose parts or cartons and

remove.

BEFORE REMOVING TRACTOR FROM

SKID

Fig. 1

LABEL

TO CHECK BATTERY (See Fig. 1)

• Lift hood to raised position.

NOTE:

If this battery is put into service after month and

year indicated on label (label is located between terminals)

charge battery for minimum of one hour at 6-10 amps.

(See "BATTERY" in Maintenance section of this manual

for charging instructions).
• For battery and battery cable installation see "RE-

PLACING BATTERY" in the "Service and Adjustments"

section in this manual.

ASSEMBLY

*Installed by Dealer

Battery

*Pedal

Slope Sheet

(1) Oil Drain Tube

(1) Quick Connect

Keys

(2) Keys

(2) Screw

(2) Nut U-Channel

(2) Hex Bolts

(2) Nut Keps

*Brush Guard Kit

Содержание GTH24V52LS/ 96048003601



































Результаты поиска

Содержание GTH24V52LS/ 96048003601

Отзывы:

Похожие инструкции для GTH24V52LS/ 96048003601

Бренды по названию

Популярные бренды

Husqvarna GTH24V52LS/ 96048003601, Руководство оператора

Результаты поиска

Содержание GTH24V52LS/ 96048003601

Отзывы:

Похожие инструкции для GTH24V52LS/ 96048003601

Бренды по названию

Популярные бренды