Husqvarna FS 6600D, Руководство оператора

Страница: 61 / 104

61
15 Accessories
BLADE GUARD CONVERSION KITS:
Use the proper size blade guard for the particular diamond
blade size being operated. The following blade guards
are available for these diamond blade sizes:
Guard Blade Sizes
60” (1500mm) 48” - 60” (1200 - 1500mm)
48” (1200mm) 36” - 48” (1000 - 1200mm)
42” (1000mm) 30” - 42” ( 750 - 1000mm)
36” ( 900mm) 24” - 36” ( 600 - 900mm)
30” ( 750mm) 18” - 30” ( 450 - 750mm)
26” ( 600mm) 14” - 26” ( 350 - 650mm)
18” ( 450mm) 14” - 18” ( 350 - 450mm)
See Blade Size Conversion charts for specific
information.
WEIGHT KITS:
Standard as on: 42” (1000mm), 48” (1200mm) &
60” (1500mm).
16 Large Diameter Models
The FS8400 / FS9900 can be con fi gured with a 60” (1500mm)
diameter blade capacity. The 60” drive can be ordered
from the factory or can be recon
fi gured by ordering the
conversion kit 542 19 96-25. See the Blade Size Conversion
Chart for speci
fi cs. Depth of cut of 25” can be achieved.
The large diameter model includes a frame extension,
60” blade guard and a blade shaft assembly with 10”
diameter fl anges. The Flanges have the following pattern.
The Blade Hole pattern must match. Six (6), ½-13 x
2.5” long Hex Head Cap Screws pass through the outer
fl ange through the blade core and thread into the inner
fl ange supplying the clamping force to hold the blade.
Use ½” lock washers with the clamping bolts. Also use
the 5/8-11 x 4.0” Cap Screw, LH or RH thread through
the center of the
fl ange. Husqvarna will supply blades
with this hole pattern.
The FS8400 / FS9900, when equipped with a 60” drive
system is very heavy and the machine balance is greatly
affected by installing or removing a blade. To counter the
large balance changes, a weight box is mounted on the
left or right rear of the saws. Weights can be easily re-
moved and added to quickly adjust the machine balance
to meet the operator’s needs.
542 19 61-72 Kit, Rear weights 2 Bars 42”
542 19 80-22 Kit, Rear weights 3 Bars 48”
542 19 97-57 Kit, Rear weights 6 Bars 60”
(includes: Side weights)
5 Bars w/ handles
OPTIONAL KITS:
542 18 11-17* Dual Light Kit
542 19 96-26 Water Pump Kit
f) Install the 20-36 drive con fi guration decals (Decal
522627702
is required). See the “Decals and Locations”
page of this manual for more information.
See Blade Size Conversion charts for speci fi c information.
WARNING: Serious injury can occur to the
operator or people in the work area if the
rotational speed (n/min) of the DIAMOND
BLADE (2E) exceeds the maximum speed
(n/min) marked on the DIAMOND BLADE (2E).
WARNING: After Shifting Gearbox, lower
GEARBOX DETENT KNOB (3-2P) or three-
speed ENGINE GEARBOX (3-2A) could
be damaged!
If gearbox seems hard to shift, a slight movement of the
blade shaft may ease movement of GEARBOX SHIFT
LEVER (3-2O) into proper gear. Never shift the Gearbox
(3-2A) with engine running!
Two Neutral positions are available in the Three Speed
ENGINE GEARBOX (3-2A). This gearbox can be shifted
into neutral if the blade rotation needs to be eliminated
while the engine is running. If the machine is equipped
with the optional BLADE CLUTCH (1Y), the BLADE
CLUTCH SWITCH (1Y) can be moved to the “0” (OFF)
position to eliminate blade rotation while the engine
is running.