manualshive.com logo in svg

Husqvarna FE 450, Руководство пользователя

Поделиться
Скачать
Husqvarna FE 450 Скачать руководство пользователя страница 66

12 SERVICE WORK ON THE CHASSIS

64

F00320-10

Main work

–

Pull the chain at the end of the chain sliding piece upward to measure chain ten-
sion

.

Info

The lower chain section

must be taut.

When the chain guard is mounted, it must be possible to pull up the chain
at least to the point where it makes contact with chain guard

.

Chain wear is not always even, so you should repeat this measurement at

different chain positions.

Chain tension

55… 58 mm (2.17… 2.28 in)

» If the chain tension does not meet the specification:

–

Adjust the chain tension. (

p. 64)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 45)

12.36

Adjusting the chain tension

Warning

Danger of accidents

 

Incorrect chain tension damages components and results in accidents.

If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear wheel bearings wear

more quickly. Some components may break if overloaded.
If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket. As a result, the rear wheel locks or

the engine will be damaged.

–

Check the chain tension regularly.

–

Set the chain tension in accordance with the specification.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 45)

–

Check the chain tension. (

p. 63)

F00321-10

Main work

–

Loosen nut

.

–

Loosen nuts

.

–

Adjust the chain tension by turning adjusting screws

left and right.

Guideline

Chain tension

55… 58 mm (2.17… 2.28 in)

Turn adjusting screws

on the left and right so that the markings on the

left and right chain adjusters are in the same position relative to reference
marks

. The rear wheel is then correctly aligned.

–

Tighten nuts

.

–

Make sure that chain adjusters

are fitted correctly on adjusting screws

.

–

Tighten nut

.

Guideline

Nut, rear wheel spindle

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters (32 mm (1.26 in))

enables different secondary ratios with the same chain length.
Chain adjusters

can be turned by 180°.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 45)

Содержание FE 450

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды