manualshive.com logo in svg

Husqvarna FE 450, Руководство пользователя

Поделиться
Скачать
Husqvarna FE 450 Скачать руководство пользователя страница 59

12 SERVICE WORK ON THE CHASSIS

57

12.23

Installing the air filter

102178-10

Main work

–

Mount the clean air filter on the air filter support.

–

Grease the air filter in area

.

Long-life grease (

p. 118)

F00467-10

–

Insert air filter and position retaining pin

in bushing

.

The air filter is correctly positioned.

–

Insert retaining tab

.

Retaining pin

is secured by retaining tab

.

Info

If the air filter is not mounted correctly, dust and dirt may enter the engine

and result in damage.

Finishing work

–

Install the air filter box cover. (

p. 56)

12.24

Cleaning the air filter and air filter box

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

Preparatory work

–

Remove the air filter box cover. (

p. 56)

–

Remove the air filter.

(

p. 56)

H00277-10

Main work

–

Wash the air filter thoroughly in special cleaning liquid and allow it to dry properly.

Air filter cleaning agent (

p. 118)

Info

Only press the air filter to dry it, never wring it out.

–

Oil the dry air filter with a high quality filter oil.

Oil for foam air filter (

p. 118)

–

Clean the air filter box.

–

Check the intake flange for damage and looseness.

Finishing work

–

Install the air filter.

(

p. 57)

–

Install the air filter box cover. (

p. 56)

Содержание FE 450

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды