Husqvarna F2203V4 Скачать руководство пользователя

Страница: 70 / 166

12 SERVICE WORK ON THE CHASSIS

12.20

Removing the air filter box cover

F02311-10

–

Pull off the air filter box cover sideways in areas

and

and take off toward the rear.

12.21

Installing the air filter box cover

S03560-10

–

Attach catch

of the air filter box in area

and push for-

ward.

–

Engage the air filter box cover in areas

and

12.22

Removing the air filter

Note

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

–

Only operate the vehicle if it is equipped with an air filter.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды