Husqvarna F2203V4 Скачать руководство пользователя

Страница: 62 / 166

12 SERVICE WORK ON THE CHASSIS

S03575-10

–

Tighten screws

Guideline

Screw, top triple
clamp

17 Nm (12.5 lbf ft)

S04826-11

–

Position the brake caliper, and mount and tighten screws

Guideline

Screw, front
brake caliper

25 Nm (18.4 lbf ft)

Loctite

243™

–

Mount the cable ties.

–

Position the brake line, the wiring harness, and the clamp.
Mount and tighten screws

Finishing work

–

Install front fender. (

p. 63)

–

Install the front wheel.

(

p. 101)

–

Install the headlight mask with the headlight. (

p. 113)

–

Check that the wiring harness, throttle cables, and brake and
clutch lines can move freely and are routed correctly.

–

Check the steering head bearing for play. (

p. 60)

–

Remove the motorcycle from the lift stand. (

p. 54)

–

Check the headlight setting. (

p. 116)

12.11

Checking the steering head bearing play

Warning

Danger of accidents

Incorrect steering head bearing play impairs the handling characteristic and

damages components.

–

Correct incorrect steering head bearing play immediately. (Your authorized Husqvarna Motorcycles
workshop will be glad to help.)

Info

If the vehicle is operated for a lengthy period with play in the steering head bearing, the bearings and the
bearing seats in the frame can become damaged over time.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 54)

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды