Husqvarna F2203V4 Скачать руководство пользователя страница 130

Страница: 130 / 166

17 TUNING THE ENGINE

128

17.7

Checking the basic position of the shift lever

Info

When driving, the shift lever must not touch the rider's boot when in the basic position.
When the shift lever keeps touching the boot, the transmission will be subject to an excessive load.

400692-10

–

Sit on the vehicle in the riding position and determine
distance

between the upper edge of your boot and the

shift lever.

Gap between the shift lever
and the top of the boot

10 … 20 mm (0.39 …
0.79 in)

» If the distance does not meet specifications:

–

Adjust the basic position of the shift lever.
(

p. 128)

17.8

Adjusting the basic position of the shift lever

401950-12

–

Remove screw

with the washers and take off shift

lever

401951-10

–

Clean gear teeth

of the shift lever and shift shaft.

–

Mount the shift lever on the shift shaft in the required position
and engage gearing.

Info

The range of adjustment is limited.
The shift lever must not come into contact with any
other vehicle components during the shift procedure.

–

Mount and tighten screw

with washers.

Guideline

Screw, shift
lever

14 Nm (10.3 lbf ft)

Loctite

243™

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды