manualshive.com logo in svg

Husqvarna F2201V1, Руководство пользователя

Поделиться
Скачать
Husqvarna F2201V1 Скачать руководство пользователя страница 88

12 BRAKE SYSTEM

86

12.1

Checking the free travel of the hand brake lever

Warning

Danger of accidents

 

The brake system fails in the event of overheating.

If there is no free travel on the hand brake lever, pressure builds up on the front brake circuit.

–

Set the free travel on the hand brake lever in accordance with the specification.

F00153-11

–

Push the hand brake lever forward and check free travel

A

.

Free travel of hand brake
lever

≥

3 mm (

≥

0.12 in)

» If the free travel does not match the specification:

–

Adjust basic position of the hand brake lever.
(

p. 86)

12.2

Adjusting the basic position of the hand brake lever

F00153-10

–

Adjust basic position of the hand brake lever to your hand
size by turning adjusting screw

1

.

Info

Turn the adjusting screw clockwise to increase the
distance between the hand brake lever and the han-
dlebar.
Turn the adjusting screw counterclockwise to
decrease the distance between the hand brake lever
and the handlebar.
The range of adjustment is limited.
Only turn the adjusting screw by hand, and do not use
force.
Do not make any adjustments while riding.

12.3

Checking the brake discs

Warning

Danger of accidents

 

Worn-out brake discs reduce the braking effect.

–

Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motor-
cycles workshop will be glad to help.)

Содержание F2201V1































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды