Husqvarna CTH1736 Скачать руководство пользователя

Страница: 21 / 52

6 STAR PATTERN BLADE

The center of this blade has a 6 star pattern. The bolt at-

tach ing this blade has

Left Hand threads

that loosens by

turning ( ) clockwise and tight en by turning (

) coun ter -

clock wise.

FIG. 22

BLADE BOLT

LEFT HAND

THREADED

LOCK

WASHER

FLAT

WASHER

BLADE

MANDREL

ASSEMBLY

6 STAR PAT-

TERN

6 STAR CEN-

TER HOLE

TRAILING

EDGE

MAINTENANCE

BATTERY

Your tractor has a battery charging system which is suf fi cient

for normal use. However, periodic charging of the battery

with an automotive charger will extend its life.
•  Keep battery and terminals clean.
•  Keep battery bolts tight.
•  Keep small vent holes open.
•  Recharge at 6-10 amperes for 1 hour.

NOTE:

The original equipment battery on your tractor is

main te nance free. Do not attempt to open or remove caps

or covers. Adding or checking level of electrolyte is not

necessary.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause

the battery to “leak” power.
• Remove battery cover.
• Disconnect BLACK battery cable first then RED bat-

tery cable and remove battery from tractor.

• Rinse the battery with plain water and dry.
•

Clean terminals and battery cable ends with wire brush

until bright.

• Coat terminals with grease or petroleum jelly.
• Reinstall battery (See “CONNECT BATTERY” in the

As sem bly sec tion of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours

of operation and replace if necessary. The belts are not

ad just able. Re place belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean

to assure proper cooling.
Do not attempt to clean fan or transmission while engine

is running or while the transmission is hot. To prevent pos-

si ble damage to seals, do not use high pressure water or

steam to clean transaxle.

•

Inspect cooling fan to be sure fan blades are intact and

clean.

• Inspect cooling fins for dirt, grass clippings and other

materials. To prevent damage to seals, do not use com-

pressed air or high pressure sprayer to clean cooling

fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid main te -

nance is not required for the life of the transaxle. Should

the transaxle ever leak or require servicing, contact your

near est au tho rized ser vice center/department.

BLADE REMOVAL

• Raise mower to highest position to allow access to

blades.

• Remove blade bolt, lock washer and flat washer se cur ing

blade.

• Install new or resharpened blade with trail ing edge up

towards deck as shown.

IMPORTANT:

To ensure proper as sem bly, center hole in

blade must align with star on mandrel assembly.
• Reassemble blade bolt, lock washer and flat washer

in exact order as shown.

• Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT

: Blade bolt is grade 8 heat treated

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service

classification SF-SJ. Select the oil’s SAE viscosity grade

according to your expected operating temperature.

Change the oil after every 50 hours of operation or at least

once a year if the tractor is not used for 50 hours in one

year.
Check the crankcase oil level before starting the engine

and after each eight (8) hours of operation.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20

100

-30

-20

-10

5W-30

10W30

oil_visc_chart4_e

Содержание CTH1736





















































Результаты поиска

Содержание CTH1736

Отзывы:

Похожие инструкции для CTH1736

Бренды по названию

Популярные бренды

Husqvarna CTH1736, Руководство пользователя

Результаты поиска

Содержание CTH1736

Отзывы:

Похожие инструкции для CTH1736

Бренды по названию

Популярные бренды