Husqvarna 967177001 Скачать руководство пользователя | Manualshive

Страница: 39 / 64

background image

39

MAINTENANCE

8058-063

Slackening the belt tensioner

8050-843

Belt routing, deck belt

Deck Belt

Deck Belt Removal

Park on a level surface. Apply park brake. Lower the
deck into the lowest cutting position.
1. Remove foot plate and belt shields.
2. Using a ratchet or breaker bar with a

9

/

16

" socket

on the spring idler bolt, relieve the tension on the
belt.

3. Remove any dirt or grass that may have

accumulated around the cutter housings and
entire deck surface.

4. Carefully roll the belt over the top of the cutter

housing pulleys.

5. Remove the belt from around the electric clutch on

the engine shaft and off the mower deck.

Deck Belt Installation

NOTE: For ease in installing the deck belt, refer to the
routing decal on the deck.
1. Wrap the deck belt around the electric clutch

pulley that is located on the engine shaft.

2. Route the belt forward between the spring loaded

and stationary pulleys.

3. Place belt around spring loaded idler pulley.
4. Wrap the belt around the stationary idler pulley

and around the mandrel housings.

5. Push inward on the idler arm and carefully route

belt over stationary idler pulley. Once belt is
properly routed, slowly release idler arm to tension
belt.

6. Check that there are not twists in the belt and that

the routing matches the routing decal.

7. Replace belt shields on both mandrel housings

and secure with fasteners.

«
...
37
38
39
40
41
...
»

Содержание 967177001

































































Отзывы:

Нет отзывов

Похожие инструкции для 967177001

Бренд: Ryobi Страницы: 8

Бренд: Qualcast Страницы: 20

Бренд: Harrier Страницы: 33

Бренд: Yardworks Страницы: 24

Бренд: Jacobsen Страницы: 106

Бренд: Toro Страницы: 28

Enviromower ENV369B

Бренд: Victa Страницы: 28

Бренд: Craftsman Страницы: 36

Бренд: The Handy Страницы: 20

Бренд: Vicon Страницы: 16

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды