manualshive.com logo in svg

Husqvarna 966613301, Руководство оператора

Поделиться
Скачать
Husqvarna 966613301 Скачать руководство пользователя страница 30

oPeRatIon

30

Weak Battery

If “jumper cables” are used for emergency starting, 
follow this procedure:

Jumper Cables

Connect each end of the RED cable to the 

• 

POSITIVE (+) terminal on each battery, taking 
care not to short against chassis.
Connect one end of the BLACK cable to the 

• 

NEGATIVE (-) terminal of the fully charged battery.
Connect the other end of the BLACK cable to a 

• 

good CHASSIS GROUND on the mower with the 
discharged battery, away from the fuel tank and 
battery.

To remove cables, reverse order

Remove BLACK cable first from chassis and then 

• 

from the fully charged battery.
Remove RED cable last from both batteries.

• 

8011-642

Jumper cable connection

IMPORTANT INFORMATION
The mower is equipped with a 12-volt negative 
grounded system. The other vehicle must also 
be a 12-volt negative grounded system. Do not 
use the mower to start other vehicles.

WARNING!
Lead-acid batteries generate 
explosive gases. Keep sparks, 
flame and smoking materials away 
from batteries. Always wear eye 
protection when around batteries.

Содержание 966613301





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды