background image

16

WARRANTY

HUSQVARNA EQUIPMENT WARRANTY

 

  

New 

750

 sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in normal 

service for a period of six (6) months for labor and up to one (1) year on parts from date of purchase by the original 

consumer purchaser or date of introduction into rental company fleet.  

Our obligation under this warranty is expressly limited to the replacement or repair at Husqvarna Construction Prod-

ucts, or at a service facility designated by us, of such part or parts if inspection shall disclose it to have been defec-

tive.  

 

This warranty does not apply to defects caused by damage, unreasonable use, faulty repairs made by others (or 

defects caused by failure to provide reasonable maintenance, while in the possession of the consumer). Further, the 

warranty is void if the product, or any of its components, are altered or modified by the consumer purchaser, or if the 

product is used in an inappropriate manner not recommended by the manufacturer.

The use of any other blade except Husqvarna Construction Products blades and skid plates will void the warranty 

and could cause internal damage to the motor.

In no event shall Husqvarna Construction Products be liable for any indirect, incidental or consequential damages 

from the sale or use of the product. This disclaimer applies both during and after the term of this warranty.

This warranty gives you specific legal rights and other possible rights, which may vary from state to state. Some 

states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or 

exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts so the 

above limitation may not apply to you.

WARRANTY

 

ON ENGINE

  

Husqvarna Construction Products does not perform warranty repairs or reimburse for warranty repairs on engines. 

Engine warranties are provided by the engine manufacturer.

To obtain warranty repair: Take your engine along with your proof of purchase to any general purpose dealer or dis-

tributor nearest you. 

If you are unable to obtain warranty service or are dissatisfied with the warranty service you received, contact the 

owner of the dealership involved. Normally, this should resolve your problem. For further assistance, call our parts 

and service department at 1-800-776-3328 or 1-951-272-2330.

COPYRIGHT 2009 HUSQVARNA CONSTRUCTION PRODUCTS

  

Covered by one or more of the following U.S. Patents

4769201, 4889675, 4928662, 4938201, 5056499, 5086750, 5184597, 5303688, 5305729, 5373834, 5441033, 

5505189, 5507273, 5570677, 5575271, 5579754, 5582899, 5603310, 5660161, 5664553, 5666939, 5689072, 

58030371, 6892719, 6990972, 7073495, 7163010, 7258115.

Other U.S. and foreign patents pending.

WARRANTY

 

ON REPLACEMENT PARTS

 

There is a three (3) months warranty from date of purchase on all replacement parts.

Содержание 750


















Отзывы: