Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 131

Страница: 131 / 216

14 WHEELS, TIRES

129

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 77)

–

Check the chain tension. (

p. 89)

14.5

Checking the rear hub rubber dampers

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

–

Always lay the wheel down in such a way that the brake disc is not damaged.

Info

The engine power is transmitted from the rear sprocket to the rear wheel via 6 rubber dampers. They eventually wear out during

operation. If the rubber dampers are not changed in time, the rear sprocket carrier and the rear hub become damaged.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 77)

–

Remove the rear wheel.

(

p. 126)

V00512-10

Main work

–

Check bearing



» If the bearing is damaged or worn:

–

Change the bearing of the rear sprocket carrier.

–

Check rubber dampers



of the rear hub for damage and wear.

» If the rubber dampers of the rear hub are damaged or worn:

–

Change all rubber dampers in the rear hub.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды