Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 128

Страница: 128 / 216

14 WHEELS, TIRES

126

14.3

Removing the rear wheel

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 77)

V00509-11

Main work

–

Press the brake caliper onto the brake disc by hand in order to push back the brake

piston.

–

Remove screw



and pull wheel speed sensor



out of the hole.

–

Remove nut



. Remove chain adjuster



–

Remove wheel spindle



–

Push the rear wheel forward as far as possible and take the chain off the rear

sprocket.

Info

Cover the components to protect them against damage.

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

–

Always lay the wheel down in such a way that the brake disc is not dam-

aged.

–

Take the rear wheel out of the swingarm.

Info

Do not operate the foot brake when the rear wheel is removed.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды