Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 129

Страница: 129 / 216

14 WHEELS, TIRES

127

14.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Warning

Danger of accidents

There is no braking effect to start with at the rear brake after installing the rear wheel.

–

Actuate the foot brake several times before going on a ride until you can feel a firm pressure point.

Main work

–

Check the rear hub rubber dampers.

(

p. 129)

H00937-11

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Remove spacer.

–

Clean and grease shaft seal ring



and contact surface



of the spacer.

Long-life grease (

p. 203)

–

Insert the spacer.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды