Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 116

Страница: 116 / 216

13 BRAKE SYSTEM

114

402027-10

–

Move the foot brake lever back and forth between the end stop and the contact to the

foot brake cylinder piston and check free travel



Guideline

Free travel at foot brake lever

3… 5 mm (0.12… 0.2 in)

Info

You will know that contact has been made with the foot brake cylinder piston

when there is increased resistance when you activate the foot brake lever.

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.

(

p. 114)

13.9

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Бренды по названию

Популярные бренды