Husqvarna 587 96 04-01 Скачать руководство пользователя страница 3

Tips For Improved Bagging

•  Follow the mower operation instructions in the Operator 

Manual.

•  When using the grass catcher on a lawn where grass 

bagging equipment has not been used previously, thatch 
and debris that has accumulated for long periods of time 
is picked up. The amount collected and the total time of 
operation may be greater than will be experienced with 
regular use of the grass catcher.

•  Always run throttle at full speed when bagging.
•  Select a speed low enough to give good mower cutting 

performance, good quality cut and good bagging 
performance. 

NOTE: It may be necessary to overlap width of cut to suit 
conditions.

•  If grass is extremely tall, it should be mowed twice. The first 

cut should be at one of the highest settings, the second 
time to desired height.

•  Use the left hand side of mower for trimming.
•  Avoid cutting wet grass or in the morning while the dew is 

still heavy. Grass clippings collected under these conditions 
tend to be sticky and adhere to the walls of the flow path 
causing clogging.

•  If the grass catcher fails to pick up cut grass, it is an 

indication that clogging has occurred in the system or that 
the grass catcher containers are full.

a.  Disengage blades, place motion control levers in 

neutral position.

 -  Unlatch and raise cover.
 -  Slide out containers and dispose of clippings.
 -  Replace containers, close cover, and latch.

b.  Unlatch chutes and check for clogging.

 -  Remove all debris in chute.
 -  Reassemble and latch chutes.

•  Plastic trash bags (3.0 mil, 30 gallon) can be inserted inside 

grass catcher containers for ease of debris disposal. To 
remove the plastic trash bags when full:

a.  Disengage blades, shift into neutral, engage the 

parking brake and stop the engine.

b.  Unlatch and raise cover.
c.  Remove one container at a time by grasping container 

handles and pulling toward the rear, off of the tube rails.

d.  With the container resting on the ground, close and 

secure the top of the plastic lawn bag.

e.  Tip the container on its side and slide the filled bag 

from the container.

f.  Install a new plastic lawn bag with the edges of the bag 

draped over upper lip of the Container.

g.  Repeat for other container.
h.  Reinstall containers making sure right container 

overlaps left container at center supports.

i.  Close cover and secure latches over center support 

tubes.

General Recommendations

Always observe safety rules when performing any 
maintenance.
• 

Before each use check for loose fasteners.

• 

Clean unit thoroughly after each use.

Blade Care

• 

For best results mower blades must be kept sharp. 
Replace bent or damaged blades.

• 

See instructions in the mower operator manual.

Storage

When grass catcher is to be stored for a period of time, clean 
it thoroughly, remove all dirt and debris. Store in a clean, dry 
place.

SAFETY ............................................................. 4

ASSEMBLY ....................................................... 6

PARTS ............................................................. 10

CONTENTS

Содержание 587 96 04-01













Отзывы: