Husqvarna 540200800 Скачать руководство пользователя страница 3

Страница: 3 / 30

Operators Guide

Height

42 in. (107 cm.)

Length

31 in. (79 cm.)

Width (without engine mount or vacuum assembly) 39 in. (99 cm.)

Width (with engine mount and vacuum assembly) 63 in. (160 cm.)

Engine Options

5.5 hp Briggs & Stratton Intek
6 hp Kohler

Weight (without vacuum assembly)

107 lb. (49 kg.)

Weight (with 6 hp Kohler vacuum assembly)

172 lb. (78 kg.)

Capacity

8.5 cu ft (7 bu. or 0.24 m

)

Hose

7 in. (18 cm.) upper and lower

Specifications

Height

42 in. (107 cm.)

Length

31 in. (79 cm.)

Width (without hose or blower)

39 in. (99 cm.)

Width (with hose and blower) 65 in. (165 cm.)

Deck Options

42”

52”

48”

61”

Weight (without spindle drive/blower assembly)

95 lb. (43 kg.)

Weight (with spindle drive/blower assembly)

155 lb. (70 kg.)

Capacity

8.5 cu ft (7 bu. or 0.24 m

)

Hose

7 in. (18 cm.) upper and lower

Auxiliary Engine (For Gen I and Gen II Units Only)

Spindle Drive (For Gen II, iZ and Mini Units Only) (Will Not Fit on 72” Decks)

Содержание 540200800































Результаты поиска

Содержание 540200800

Отзывы:

Похожие инструкции для 540200800

Бренды по названию

Популярные бренды

Husqvarna 540200800, Руководство оператора

Результаты поиска

Содержание 540200800

Отзывы:

Похожие инструкции для 540200800

Бренды по названию

Популярные бренды