Husqvarna 525 LST Скачать руководство пользователя страница 10

Страница: 10 / 36

• Open the fuel cap slowly so that any excess

pressure is released gently when you refuel.

• Tighten the fuel cap carefully after you refueled.
• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Always move the product 3m (10ft) or further from

the refuelling area and source before starting.

Safety instructions for maintenance

WARNING: Always stop the engine before

you do any work on the cutting attachment.

The cutting attachment continues to rotate

even after the throttle has been released.

Ensure that the cutting attachment has

stopped completely and disconnect the

spark plug before you start to work on it.

WARNING: A faulty cutting attachment may

increase the risk of accidents.

WARNING: Make sure that the trimmer cord

is wound tightly and evenly around the

drum, otherwise the product will generate

harmful vibration.

• Only use cutting attachments with the guards we

recommend. Refer to

Accessories on page 26

Assembly

Introduction

WARNING: Before you assemble the

product, you must read and understand the

safety chapter.

WARNING: Remove the spark plug cable

from the spark plug before you assemble the

product.

To assemble the loop handle (525LST,

525RJD)

1. Attach the loop handle onto the shaft between the

arrows.

2. Install the spacer into the slot of the loop handle.
3. Attach the nut, the knob and the screw. Do not make

it too tight.

4. Adjust the product to a correct work position.
5. Tighten the bolt.

To assemble the J-handle (525LST,

525RJD)

WARNING: Do not use saw blades with the

J-handle.

1. Attach the J-handle to the loop handle with 3 screws.

Do not tighten the screws fully.

2. Adjust the product to a comfortable position.
3. Tighten the screws.

1363 - 001 - 25.10.2019

Содержание 525 LST





































Результаты поиска

Содержание 525 LST

Отзывы:

Похожие инструкции для 525 LST

Бренды по названию

Популярные бренды

Husqvarna 525 LST, Руководство оператора

Результаты поиска

Содержание 525 LST

Отзывы:

Похожие инструкции для 525 LST

Бренды по названию

Популярные бренды