manualshive.com logo in svg

Husqvarna 524ST, Руководство пользователя

Поделиться
Скачать
Husqvarna 524ST Скачать руководство пользователя страница 29

29

KEY   PART                
NO.    NO.                     DESCRIPTION

   1    532 18 10-44   Spring, Traction Idler
   2    532 18 05-22   Pulley, Idler (2-1/4)
   3           - - -            Engine, Tecumseh, Model Number HSSK55
                                 (Order parts from Engine manufacturer)
   4    874 78 05-20   Screw, Hex Head  5/16-18 x 1-1/4
   5   

532 15 00-78

  Screw, Hex Washer Head  5/16-18 x 3/4

   6    532 05 92-89   Washer, Flat
   7    873 93 05-00   Nut, Jam, Lock  5/16-18
   8    532 17 53-30   Pin, Idler Pivot
   9    532 17 90-92   V-Belt, Traction Drive

10    810 04 05-00   Washer, Lock  5/16
11    817 49 05-08   Screw, Hex Head  5/16-18 x 1/2
12    532 17 92-59   Idler Arm Assembly, Impeller
13    532 08 51-79   Retainer, Hairpin
14    532 17 88-28   Spring, Brake
15    532 18 35-33   V-Belt, Impeller Drive
16    532 15 04-06   Screw, Hex Head  3/8-16 x 1-1/4
17    532 18 48-04   Arm, Idler
18    874 78 05-24   Screw, Hex Head  5/16-18 x 1-1/2
19    532 17 53-31   Bushing, Idler Pivot
20    532 18 05-23   Pulley, Idler (2-3/4)
21    874 61 05-16   Screw, Hex Head  5/16-24 x 1
22    532 17 93-71   Spacer, Engine Pulley
23    532 18 04-78   Pulley, Engine, Traction Drive
24    532 17 91-57   Pulley, Engine, Impeller Drive
25    532 06 27-35   Washer, Flat  3/8
26    532 85 02-63   Washer, Lock  3/8
27    532 85 10-84   Screw, Hex Head  3/8-24 x 1-3/8
28    532 18 35-61   Guide, Belt
29    532 18 04-65   Cover, Belt
30    532 17 88-30   Cover, Toolbox
31    817 49 04-08   Screw, Hex Head  1/4-20 x 1/2
32    532 17 92-56   Bolt, Shoulder  5/16-18
33    532 18 78-53   Bellcrank Shifter
34    532 18 04-01   Screw, Hex Head  1/4-28 x 3/4
35    532 17 92-40   Arm, Auger Control
36    873 80 05-00   Nut, Lock  5/16-18
37    532 18 40-86   Bellcrank Assembly
38    532 18 71-01   Link, Speed Control
39    532 17 90-64   Trunnion, Clutch
40    532 17 88-90   Nut, Cage  3/8-16
41    532 70 02-79   Hairpin, Cotter  3/32 x 1/2
42    532 17 90-65   Pin, Bellcrank
43    532 18 40-85   Bracket, Bellcrank
44    874 78 06-24   Screw, Hex Head  3/8-16 x 1-1/2
45    532 18 40-74   Pivot Bracket, Impeller Idler Arm
46    532 18 40-84   Pan, Frame Bottom
47    871 02 05-12   Screw, Hex Head  5/16-18 x 3/4
48    532 18 11-56   Nut, Speed  5/16-18
49    532 18 40-73   Frame Assembly
50    532 18 80-02   Plate, Frame End
51    532 18 40-82   Shaft, Auger Control
52    532 05 70-79   Washer, Hardened
53    532 17 90-62   Roller
54    812 00 00-10   Ring, Retaining

NOTE:

  All component dimensions given in U.S. inches.  1 inch = 25.4 mm

REPAIR PARTS

                                                       CHASSIS / ENGINE / PULLEYS

SNOW THROWER - - MODEL NO. 524ST (HL524STA), PRODUCT NO. 954 63 35-52

Содержание 524ST

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды