Husqvarna 4421-DXL Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 68

background image

General Information

1403

Figure 4

Dispose of Lead-acid Batteries Properly

GENERAL INFORMATION

This manual includes operating procedures, maintenance, and regular servicing information for all gasoline and diesel
HUV 4421-G and HUV 4421-D vehicles. GXP and DXP models have been renamed GX and DX, respectively. All
operating procedures, maintenance, and regular servicing are identical unless otherwise noted.

MODEL IDENTIFICATION

The serial number of each vehicle is printed on a bar code decal mounted either below the passenger side cup holder
or above the accelerator or brake pedal (Example: PH0901-583947)

(Figure 5)

.

The two letters (1) at the beginning of the serial number indicate the vehicle model. The following four digits (2)
indicate the model year and production week during which the vehicle was built. The six digits (3) following the hyphen
represent the unique sequential number assigned to each vehicle built within a given model year.

See following NOTE.

NOTE:

Have the vehicle serial number available when ordering parts or making inquiries.

A 17-digit Product Information Number (PIN) is included on this vehicle next to the serial number. This number
may be used to register the vehicle where required.

Build Code:

The build code (4) is a five-digit number that appears on the vehicle serial number decal. The build code

exists to enable the user to identify the correct owner’s manual for a vehicle. This owner’s manual is valid for the build
code range indicated on the back cover of this owner’s manual.

Page 14

HUV 4421 Owner’s Manual

«
...
14
15
16
17
18
...
»

Содержание 4421-DXL





































































Отзывы:

Нет отзывов

Похожие инструкции для 4421-DXL

Бренд: Chongqing Astronautic Bashan Motorcycle Manufacturing Страницы: 16

Бренд: Sinclair Страницы: 36

Бренд: KAYO MOTOR Страницы: 96

Бренд: KAYO MOTOR Страницы: 96

ski-doo REV GEN4 TOURING ACE

Бренд: BRP Страницы: 340

Бренд: Apogee Страницы: 24

Бренд: PRONAR Страницы: 166

Бренд: Miller Electric Страницы: 20

Бренд: Leggero Страницы: 98

Minor VM Hydrostatic

Бренд: Scarab Страницы: 32

Бренд: Yerf-Dog Страницы: 25

Бренд: Taylor-Dunn Страницы: 232

EVINRUDE Johnson 5007118

Бренд: BRP Страницы: 14

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 158

Бренд: Yamaha Страницы: 320

Бренд: Yamaha Страницы: 52

Бренд: Bailey Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды