background image

WORKING TECHNIQUES

16 – English

Basic working techniques

Safety instructions while working

Always ensure you have a safe and stable working 
position.

Always hold the machine with both hands. Hold the 
machine on the right side of your body.

Use your right hand to control the throttle setting.

Make sure that your hands and feet do not come near 
the cutting attachment when the engine is running.

When the engine is switched off, keep your hands and 
feet away from the cutting attachment until it has 
stopped completely.

Always carry out edging at full throttle.

Always keep the blade close to the ground.

Always slow the engine to idle speed after each 
working operation. Long periods at full throttle without 
any load on the engine (i.e. without the resistance that 
the cutting attachment exerts on the engine when you 
are using the machine) can lead to serious engine 
damage.

Be especially careful when pulling the edger towards 
you during work.

If any foreign object is hit or if vibrations occur stop the 
machine immediately. Disconnect the HT lead from 
the spark plug. Check that the machine is not 
damaged. Repair any damage.

Safety instructions after completing work

Make sure the cutting attachment has stopped before 
cleaning, carrying out repairs or an inspection. 
Disconnect the HT lead from the spark plug. 

Always wear heavy-duty gloves when repairing the 
cutting attachment. This is extremely sharp and can 
easily cause cuts.

Store the machine out of reach of children.

Use only original spare parts for repairs.

!

WARNING! Sometimes grass or stones 
can get trapped in the cutter guard and 
cutter. Always stop the engine before 
cleaning.

!

WARNING! Watch out for thrown objects. 
Always wear approved eye protection. 
Never lean over the cutting attachment 
guard. Stones, rubbish, etc. can be 
thrown up into the eyes causing 
blindness or serious injury.

!

WARNING! Overexposure to vibration 
can lead to circulatory damage or nerve 
damage in people who have impaired 
circulation. Contact your doctor if you 
experience symptoms of overexposure 
to vibration. Such symptoms include 
numbness, loss of feeling, tingling, 
pricking, pain, loss of strength, changes 
in skin colour or condition. These 
symptoms normally appear in the 
fingers, hands or wrists. The risk 
increases at low temperatures.

H1153175-95,426Ex,US.fm  Page 16  Monday, November 30, 2009  11:20 AM

Содержание 426EX

























Отзывы: