background image

MAINTENANCE

16 – English

Carburettor

Your Husqvarna product has been designed and 
manufactured to specifications that reduce harmful 
emissions. After the engine has used 8-10 tanks of fuel 
the engine will be run-in. To ensure that it continues to run 
at peak performance and to minimise harmful exhaust 
emissions after the running-in period, ask your dealer/
service workshop (who will have a rev counter at their 
disposal) to adjust your carburettor.

Function

The carburettor governs the engine’s speed via the 
throttle control. Air and fuel are mixed in the 
carburettor. The air/fuel mixture is adjustable. Correct 
adjustment is essential to get the best performance 
from the machine.

Adjusting the carburettor means that the engine is 
adapted to local operating conditions, e.g. climate, 
altitude, petrol and the type of 2-stroke oil.

The carburettor has three adjustment controls:

L = Low speed jet

H = High speed jet

T = Idle adjustment screw

The L and H-jets are used to adjust the supply of fuel 
to match the rate that air is admitted, which is 
controlled with the throttle. If they are screwed 
clockwise the air/fuel ratio becomes leaner (less fuel) 
and if they are turned anti-clockwise the ratio 
becomes richer (more fuel). A lean mixture gives a 
higher engine speed and a rich mixture gives a lower 
engine speed.

The T-screw regulates the throttle setting at idle 
speed. If the T-screw is turned clockwise this gives a 
higher idle speed; turning it anti-clockwise gives a 
lower idle speed.

Basic setting

The basic carburettor settings are adjusted during 
testing at the factory. The basic setting is richer than 
the optimal setting and should be maintained for the 
first few hours the machine is in use. The carburettor 
should then be finely adjusted. Fine adjustment 
should be carried out by a skilled technician.

CAUTION! 

 If the blades move while the engine is idling 

the T screw should be turned anti-clockwise until they 
stop.

Rec. idle speed:

 2700 rpm

Recommended max. speed:

 See the Technical data 

section.

Fine adjustment

When the machine has been ”run-in” the carburettor 
should be finely adjusted. The fine adjustment should 
be carried out by a qualified person. First adjust the L-
jet, then the idling screw T and then the H-jet.

Conditions

Before any adjustments are made, make sure that the 
air filter is clean and the air filter cover is fitted. If you 
adjust the carburettor when the air filter is dirty it will 
result in a leaner mixture when the filter is finally 
cleaned. This can lead to serious engine damage.

Carefully turn both jets, L and H, so that they are 
midway between fully screwed in and fully screwed 
out.

Do not attempt to adjust the L and H jets beyond either 
stop as this could cause damage.

Now start the machine according to the starting 
instructions and let it warm up for 10 minutes.

CAUTION! 

 If the blades move while the engine is idling 

the T screw should be turned anti-clockwise until they 
stop.

!

WARNING! The complete clutch cover 
and gear housing must be fitted before 
the machine is started, otherwise the 
clutch may come loose and cause 
personal injury.

!

WARNING! If the idle speed cannot be 
adjusted so that the cutting attachment 
stops, contact your dealer/service 
workshop. Do not use the machine until 
it has been correctly adjusted or 
repaired.

Содержание 326HD60X series





























Отзывы: