background image

24 – 

English

FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND 
OBLIGATIONS

The EPA (U.S. Environmental Protection Agency), CARB 
(California Air Resources Board), Environment Canada and 
Husqvarna Forest & Garden are pleased to explain the 
emissions control system’s warranty on your 2007 and later 
small off-road engine. In U.S. and Canada, new equipment 
that use small off-road engines must be designed, built, and 
equipped to meet the applicable Federal or Californian 
stringent anti-smog standards. Husqvarna Forest & Garden 
must warrant the emissions control system on your small off-
road engine for the period listed below provided there has 
been no abuse, neglect or improper maintenance of your 
equipment. Your emissions control system may include parts 
such as the carburetor, ignition system, catalytic converter, 
fuel tank, filters and other associated components. Also, 
included may be hoses, belts, connectors, sensors, and other 
emission-related assemblies. Where a warrantable condition 
exists, Husqvarna Forest & Garden will repair your small off-
road engine at no cost to you including diagnosis, parts and 
labor.

MANUFACTURER

′′′′

S WARRANTY 

COVERAGE

The emissions control system is warranted for two years. If 
any emissions-related part on your equipment is defective, 
the part will be repaired or replaced by Husqvarna Forest & 
Garden.

OWNER

′′′′

S WARRANTY RESPONSIBILITIES

As the small off-road engine owner, you are responsible 
for performance of the required maintenance listed in your 
operator’s manual. Husqvarna Forest & Garden 
recommends that you retain all receipts covering 
maintenance on your small off-road engine, but 
Husqvarna Forest & Garden cannot deny warranty solely 
for the lack of receipts or your failure to ensure the 
performance of all scheduled maintenance.

As the small off-road engine owner, you should however 
be aware that Husqvarna Forest & Garden may deny you 
warranty coverage if your small off-road engine or a part 
has failed due to abuse, neglect, or improper maintenance 
or unapproved modifications.

You are responsible for presenting your small off-road 
engine to a Husqvarna Forest & Garden distribution 
center or service center as soon as the problem exists. 
The warranty repairs should be completed in a reasonable 
amount of time, not to exceed 30 days. If you have any 
questions regarding your warranty coverage, you should 
contact Husqvarna Forest & Garden at 1-800-487-5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date the engine or 
equipment is delivered to an ultimate purchaser.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the ultimate 
purchaser and each subsequent owner that the engine or 
equipment is designed, built, and equipped so as to conform 
with all applicable regulations adopted by EPA and CARB, 

and is free from defects in materials and workmanship that 
causes the failure of a warranted part for a period of two 
years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

 Repair or 

replacement of any warranted part under the warranty must 
be performed at no charge to the owner at a warranty station. 
Warranty services or repairs will be provided at all Husqvarna 
Forest & Garden distribution centers that are franchised to 
service the subject engines. Throughout the emissions 
warranty period of two years, Husqvarna Forest & Garden 
must maintain a supply of warranted parts sufficient to meet 
the expected demand for such parts.

WARRANTY PERIOD

 Any warranted part that is scheduled 

for replacement as required in the maintenance schedule, is 
warranted for the period of time prior to the first scheduled 
replacement point for that part. If the part fails prior to the first 
scheduled replacement, the part will be repaired or replaced 
by Husqvarna Forest & Garden at no cost. Any such part 
repaired or replaced under warranty is warranted for the 
remainder of the period prior to the first scheduled 
replacement point for the part. Any warranted part that is not 
scheduled for replacement as required in the maintenance 
schedule, is warranted for two years. If any such part fails 
during the period of warranty coverage, it will be repaired and 
replaced by Husqvarna Forest & Garden at no cost. Any such 
part repaired or replaced under the warranty is warranted for 
the remaining warranty period. Any warranted part that is 
scheduled only for regular inspection in the maintenance 
schedule will be warranted for a period of two years. A 
statement in such written instructions to the effect of ”repair or 
replace as necessary” will not reduce the period of warranty 
coverage. Any such part repaired or replaced under warranty 
will be warranted for the remaining warranty period.

DIAGNOSIS

 The owner must not be charged for diagnostic 

labor that leads to the determination that a warranted part is 
in fact defective, provided that such diagnostic work is 
performed at a warranty station.

CONSEQUENTIAL DAMAGES

 Husqvarna Forest & Garden 

is liable for damages to other engine components proximately 
caused by a failure under warranty of any warranted part.

EMISSION WARRANTY PARTS LIST

1

Carburetor and internal parts

2

Intake pipe, airfilter holder and carburetor bolts.

3

Airfilter and fuelfilter covered up to maintenance schedule.

4

Spark Plug, covered up to maintenance schedule

5

Ignition Module

6

Muffler with catalytic converter

7

Fuel tank

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper 
maintenance are not covered.

Содержание 324LX Series

































Отзывы: