background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

8

 

 – 

 

English

 

be chec

 

ked. See instructions under the heading 

Maintenance.

 

Stop s

 

witch

 

Use the stop s

 

witch to switch off the engine.

Start the engine and make sure the engine stops when 
you move the stop switch to the stop setting.

 

Cutting attac

 

hment guard

 

This guard is intended to pre

 

vent loose objects from being 

thrown towards the operator. The guard also protects the 
operator from accidental contact with the cutting 
attachment.

Check that the guard is undamaged and not cracked. 
Replace the guard if it has been exposed to impact or is 
cracked.

Always use the recommended guard for the cutting 
attachment you are using. See chapter on Technical data.

 

Vibration damping system

 

Y

 

our machine is equipped with a vibration damping 

system that is designed to reduce vibration and make 
operation easier.

Use of incorrectly wound cord or an incorrect cutting 
attachment increases the level of vibration. See 
instructions under the heading Cutting equipment.

The machine

 

 

s vibration damping system reduces the 

transfer of vibration between the engine unit/cutting 
equipment and the machine

 

 

s handle unit.

Regularly check the vibration damping units for cracks or 
deformation. Check that the vibration damping element is 
undamaged and securely attached.

 

Muffl

 

er

 

The muffler is designed to keep noise levels to a minimum 
and to direct exhaust fumes away from the user. A muffler 

!

WARNING! Never use a cutting 
attachment without an approved guard. 
See the chapter on Technical data. If an 
incorrect or faulty guard is fitted this can 
cause serious personal injury.

!

WARNING! Overexposure to vibration 
can lead to circulatory damage or nerve 
damage in people who have impaired 
circulation. Contact your doctor if you 
experience symptoms of overexposure 
to vibration. Such symptoms include 
numbness, loss of feeling, tingling, 
pricking, pain, loss of strength, changes 
in skin colour or condition. These 
symptoms normally appear in the 
fingers, hands or wrists. The risk 
increases at low temperatures.

Содержание 324LDX Series





































Отзывы: