background image

24 – 

English

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND 
OBLIGATIONS

The EPA (The US Environmental Protection Agency), 
Environment Canada and Husqvarna Forest & Garden are 
pleased to explain the emissions control system warranty on 
your 2001 and later small nonroad engine. In U.S. and 
Canada, new small nonroad engines must be designed, built 
and equipped to meet the federal stringent anti-smog 
standards. Husqvarna Forest & Garden must warrant the 
emission control system on your small nonroad engine for the 
period of time listed below provided there has been no abuse, 
neglect or improper maintenance of your unit. Your emission 
control system includes Parts such as the carburetor and the 
ignition system. Where a warrantable condition exists, 
Husqvarna Forest & Garden will repair your small nonroad 
engine at no cost to you. Expenses covered under warranty 
include diagnosis, parts and labor.

MANUFACTURER

′′′′

S WARRANTY 

COVERAGE

The 2001 and later small nonroad engines are warranted for 
two years. If any emission related part on you engine (as 
listed above) is defective, the part will be repaired or replaced 
by Husqvarna Forest & Garden.

OWNER

′′′′

S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for 
the performance of the required maintenance listed in your 
Operator

s Manual. Husqvarna Forest & Garden 

recommends that you retain all receipts covering 
maintenance on your small nonroad engine, but Husqvarna 
Forest & Garden cannot deny warranty solely for the lack of 
receipts or for your failure to ensure the performance of all 
scheduled maintenance. As the small nonroad engine owner, 
you should, however, be aware that Husqvarna Forest & 
Garden may deny you warranty coverage if your small 
nonroad engine or a part of it has failed due to abuse, neglect, 
improper maintenance, unapproved modi

fi

cations or the use 

of parts not made or approved by the original equipment 
manufacturer. You are responsible for presenting your small 
nonroad engine to a Husqvarna Forest & Garden authorized 
servicing dealer as soon as a problem exists. The warranty 
repairs should be completed in a reasonable amount of time, 
not to exceed 30 days. If you have any questions regarding 
your warranty rights and responsibilities, you should contact 
your nearest authorized servicing dealer or call Husqvarna 
Forest & Garden at 1-800-487-5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine 
is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner and 
each subsequent purchaser that the engine is free from 
defects in materials and workmanship which cause the failure 
of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

 Repair or 

replacement of any warranted part will be performed at no 
charge to the owner at an approved Husqvarna Forest & 
Garden servicing dealer. If you have any questions regarding 
your warranty rights and responsibilities, you should contact 
your nearest authorized servicing dealer or call Husqvarna 
Forest & Garden at 1-800-487-5963.

WARRANTY PERIOD

 Any warranted part which is not 

scheduled for replacement as required maintenance, or 
which is scheduled only for regular inspection to the effect of 
“repair or replace as necessary” shall be warranted for 2 
years. Any warranted part which is scheduled for replacement 
as required maintenance shall be warranted for the period of 
time up to the 

fi

rst scheduled replacement point for that part.

DIAGNOSIS

 The owner shall not be charged for diagnostic 

labor which leads to the determination that a warranted part 
is defective, if the diagnostic work is performed at an 
approved Husqvarna Forest & Garden servicing dealer.

CONSEQUENTIAL DAMAGES

 Husqvarna Forest & Garden 

may be liable for damages to other engine components 
caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper 
maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modi

fi

ed parts can be grounds for 

disallowing a warranty claim. Husqvarna Forest & Garden is 
not liable to cover failures of warranted parts caused by the 
use of add-on or modi

fi

ed parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and 
responsibilities, you should contact your nearest authorized 
servicing dealer or call Husqvarna Forest & Garden at 1-800-
487-5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all 
Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND 
REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part 
used in the performance of any warranty maintenance or 
repairs on emission-related parts, will be provided without 
charge to the owner if the part is under warranty.

Содержание 323HE3





























Отзывы: