Husqvarna 323Ex Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 28

Husqvarna 323Ex Series Скачать руководство пользователя страница 11

ASSEMBLY

English

–

11

1153252-95 Rev.1 2010-02-02

Fitting the loop handle

•

Position the handle on the shaft. Note that the handle
must be mounted below the arrow on the shaft.

•

Fit the bolt, securing plate and wing nut as shown in
the diagram.

•

Tighten the wing nut.

Assembling the angle gear

•

Assemble the angle gear back on the suppporting
tube. Turn the blade so that the drive shaft engages in
the angle gear.

•

Position the angle gear so that its slot is aligned with
the line on the supporting tube.

•

Firmly tighten the screw.

Assembling the cutting
equipment

Assembling the blade

Fit the blade as follows:

1

Fit the drive disc (A) on the outgoing shaft. Make sure
that the edge that fits in the hole of the blade is facing
outward.

2

Block the blade rotation by inserting the locking pin in
the hole behind the blade guard engaging it in the
corresponding hole in the drive disc.

3

Fit the blade (B) on the drive disc.

4

Fit the support flange (C). The support flange must be
fitted with its outer edge hard up against the blade.

!

WARNING!

When fitting the cutting attachment it is
extremely important that the raised
section on the drive disc/support flange
engages correctly in the centre hole of
the cutting attachment. If the cutting
attachment is fitted incorrectly it can
result in serious and/or fatal personal
injury.

!

WARNING! Under no circumstances may
the edge cutter blade be used without the
blade guard fitted.

«
...
9
10
11
12
13
...
»

Содержание 323Ex Series





























Отзывы:

Нет отзывов