Husqvarna 250211 Скачать руководство пользователя | Manualshive

Страница: 37 / 64

background image

1

2

2

MAINTENANCE

37

Battery

Your mower is equipped with a maintenance free
battery and does not need servicing. However,
periodic charging of the battery with an automotive
type battery charger will extend its life.
•  Keep battery and terminals clean.
•  Keep battery bolts tight.
•  See chart for charging times.

IMPORTANT INFORMATION
Do not attempt to open or remove caps or
covers. Adding or checking level of electrolyte
is not necessary.
Always use two wrenches for the terminal
screws.

WARNING!
Do not short battery terminals by
allowing a wrench or any other object
to contact both terminals at the same
time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
Positive terminal must be connected
first to prevent sparks from accidental
grounding.

Corrosion and dirt on the battery and terminals can
cause the battery to lose power.
1. Open the terminal access doors.
2. Disconnect BLACK battery cable first, then the

RED battery cable and remove the battery from
the machine.

3. Rinse the battery with plain water and dry.
4. Clean terminals and battery cable ends with wire

brush until shiny.

5. Coat terminals with grease or petroleum jelly.
6. Reinstall battery.

Replacing battery

1.  Lift seat and rotate forward.
2.  Open terminal access doors
3.  Using two ½" wrenches disconnect BLACK

battery cable then RED battery cable.

4. Using a

7

/

16

wrench, remove the bolts on either

side of the terminal guard and lift off guard.

5. Carefully remove the battery from the mower.
6. Install new battery with terminals in the same

position as the old battery.

7. Reinstall battery terminal guard.
8. Connect RED battery cable to positive (+) battery

terminal with hex bolt and hex nut.

9. Connect BLACK grounding cable to negative (-)

battery terminal with remaining hex bolt and hex
nut.

10. Close access doors.
11. Lower seat.

8066-049

1. Terminal guard
2. Access doors

Battery cleaning and installation

STANDARD

BATTERY

STATE

OF

CHARGE

APPROXIMATE BATTERY CHARGING TIME*

TO FULL CHARGE AT 80

O

F / 27

O

C

Maximum Rate at:

50 Amps

30 Amps

20 Amps

10 Amps

12.6V

100%

- FULL CHARGE -

12.4V

75%

20 min.

35 min.

48 min.

90 min.

12.2V

50%

45 min.

75 min.

95 min.

180 min.

12.0V

25%

65 min.

115 min.

145 min.

280 min.

11.8V

0%

85 min.

150 min.

195 min.

370 min.

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

CAUTION!
Always wear eye protection when
around batteries.

«
...
35
36
37
38
39
...
»

Содержание 250211

































































Отзывы:

Нет отзывов

Похожие инструкции для 250211

Бренд: Walker Страницы: 76

Бренд: Lawn-Boy Страницы: 32

Бренд: Walker Страницы: 60

Бренд: Yard Machines Страницы: 72

Бренд: MTD Страницы: 12

Бренд: Worx Страницы: 16

Бренд: Kärcher Страницы: 12

Бренд: Ryobi Страницы: 16

Бренд: Jacobsen Страницы: 148

Бренд: Yard force Страницы: 25

Soft Touch 2.8 HM Classic

Бренд: AL-KO Страницы: 7

Бренд: Yard-Man Страницы: 11

Бренд: Rally Страницы: 24

Бренд: Yard-Man Страницы: 12

Бренд: Worx Страницы: 132

Бренд: Toro Страницы: 24

Бренд: Yard-Man Страницы: 20

Бренд: Yard Pro Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды