Husqvarna 2007 HUV 4213-G Скачать руководство пользователя страница 40

Страница: 40 / 48

Vehicle Specifications

Page 38

2007 HUV4213 Gasoline Vehicle Owner’s Manual

VEHICLE SPECIFICATIONS

SPECIFICATIONS

HUV4213-GXP

HUV4213-G

POWER SOURCE

Engine:

4-cycle OHV, 400 cc, 13.0 maximum HP @3600 rpm (per SAE J 1940/1349), single-

cylinder, air-cooled, with pressure lubrication system

•

Fuel system:

Side-draft carburetor with float bowl, fixed jets, fuel filters, and impulse fuel pump

•

Governor:

Automatic ground-speed sensing, internally geared in unitized transaxle

•

Ignition:

Transistor electronic ignition with electronic RPM limiter

•

Unitized transaxle, MC012C-BS00:

Fully synchronized forward and reverse with neutral

(14.9:1 forward, 20.5:1 reverse) and differential lock feature

•

Electrical system:

12-volt, 500 cca at 0 °F (-17.8 °C), 650 at 32 °F (0 °C). 105-minute reserve

capacity and 35-amp charging capacity

•

Torque converter:

Automatic, variable-speed, dry type

•

STEERING/SUSPENSION/BRAKES

Steering:

Self-adjusting rack and pinion, Ackerman

•

Suspension:

Front:

Independent A-arms with coil-over shocks

Rear:

Semi-independent suspension with multi-leaf springs and dual hydraulic shocks

•

Brakes

: Hydraulic brake system – self-adjusting drum brakes on each wheel with separate

hand-operated park brake

•

BODY/CHASSIS

Frame/Chassis:

Twin I-Beam welded aluminum

•

Side and rear body:

All aluminum

•

Cargo bed:

Powder-coated steel

•

Front body:

ABS/DR acrylic cap

•

Tires

: 23 x 10.50 – 12 tubeless, 4-ply rated load range, front and rear

•

DIMENSIONS/WEIGHT

Overall length

(box bed configuration)

123.4 in. (313.4 cm)

Overall width

54 in. (137 cm)

Overall height

(at lamp bar)

75 in. (187.5 cm)

Wheelbase

80 in. (203 cm)

Ground clearance:

under differential
under foot platform

6.6 in. (17 cm)

11.4 in. (29 cm)

Front wheel tread

43 in. (109 cm)

Rear wheel tread

44.5 in. (111 cm)

Weight

(dry):

with all-terrain tread
with turf tread

1106 lb. (493.4 kg)
1066 lb. (477.2 kg)

1063.5 lb. (482.4 kg)
1027.8 lb. (466.2 kg)

Forward speed

17-19 mph (27-31 km/h)

Governed RPM:

FE400 Engine

3850 (±30) RPM

Curb clearance circle

(diameter)

24 ft. 1 in. (734 cm)

Turning radius

(per SAE J 695)

139.6 in. (355 cm)

Intersecting aisle clearance

112.2 in (285 cm)

Floorboard height

17 in. (43 cm)

Specifications continued on next page...

Содержание 2007 HUV 4213-G

















































Результаты поиска

Содержание 2007 HUV 4213-G

Отзывы:

Похожие инструкции для 2007 HUV 4213-G

Бренды по названию

Популярные бренды

Husqvarna 2007 HUV 4213-G, Руководство пользователя

Результаты поиска

Содержание 2007 HUV 4213-G

Отзывы:

Похожие инструкции для 2007 HUV 4213-G

Бренды по названию

Популярные бренды