background image

Cleaning the Vehicle

Page 34

2005 HUV4213 Gasoline Vehicle Owner’s Manual

Be sure battery hold-down clamp is properly tightened. Tighten to 12 ft-lb (16.3 N·m). A loose clamp may
allow the battery to become damaged from vibration or jarring.

If battery appears weak, have it charged by a trained technician. The battery should never be left discharged
any longer than absolutely necessary (do not leave discharged overnight).

CLEANING THE VEHICLE

Each vehicle is equipped with an ABS/DR acrylic front body and an all-aluminum rear body. The HUV4213
has a powder-coated steel cargo bed. Use commercial automotive cleaning solutions with a sponge or soft
cloth for normal cleaning. A garden hose at normal residential water pressure is adequate. To remove oxida-
tion or discoloration from aluminum, use a commercially available aluminum cleaner paste and fine grade
(No. 00) steel wool.

Husqvarna does not recommend any type of pressure washing or steam cleaning. Such a process will expose
electrical components to moisture. Moisture entering electrical components can result in water damage and
subsequent component failure.

Use non-abrasive wax products. Battery acid, fertilizers, tars, asphalt, creosote, paint, or chewing gum should
be removed immediately to prevent possible stains.

The front body is made of an ABS/DR acrylic cap material similar to the material used to manufacture hot tubs
and shower/tub units. Cleaning and repair techniques for the front body are the same as those used on con-
ventional acrylic sheet. Use cleaning and polishing products available at any hardware store where ABS/DR
acrylic (hot tubs and shower/tub units) are sold.

The seats of the vehicle will last longer with proper cleaning. Use a solution of 10% liquid soap and warm
water applied with a soft cloth. For imbedded dirt, a soft bristle brush may be used. For heavy soiling, difficult
stains, or scratches, blemishes, or other body damage, see the appropriate maintenance and service manual.

See following NOTE.

NOTE:

Dispose of waste water properly.

ACCESSORIES

There is a complete line of accessory equipment available from Husqvarna and our dealers/distributors. You
can obtain the name and phone number of your closest Husqvarna contact by visiting our web site at
www.usa.husqvarna.com.

Care should be taken that these accessories are properly installed by trained technicians, and that they are
used in the manner for which they were designed. 

See following WARNING.

ý 

WARNING

• Custom cab assemblies, canopy tops, weatherproof enclosures, and windshields will not

protect occupants from flying objects.

• If the vehicle is equipped with an electric powered bed lift, remove the bed before servicing

the bed lift system.

Содержание 2005 HUV4213















































Отзывы: